■
Specifications
Size
150mm (dia.) X 27mm (H) (Excluding the jack cable)
Weight
330g (Including the jack cable)
Sensor System
Trigger Sensor (Piezo) x 1
Output Jack
Standard Monaural Phone Jack
Accessories
Monaural PhoneCable (1.5m) x 1
Attachment Set x1 (Wing Nut, Felt(Large), Felt(Small), Cable Band, 1 each)
Owner’s Manual (this booklet) x 1
*Improvements may result in a change in the specifications and/or design of the product without notice.
Printed in Japan
V923790
SPESIAL MESSAGE SECTION
NOTICE:
Service charges incurred due to a lack of knowledge relathing to how a function or effect works (when the unit is operating as designed) are not covered by
the manufacturer’s warranty, and are therefore the owners responsibility. Please study this manual carefuly and consult your dealer before requesting service.
ENVIRONMENTAL ISSUES:
Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely believe that our products and the
production methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you to be aware of the following:
Battery Notice:
This product MAY contain a small non-rechargeable battery which (if applicable) is soldered in place. The average life span of this type of battery is
approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement.
This product may also use “household” type batteries. Some of these may be rechargeable. Make sure that the battery being charged is a rechargeable type and that
the charger is intended for the battery being charged.
When installing batteries, do not mix batteries with new, or with batteries of a different type. Batteries MUST be installed correctly. Mismatches or incorrect installation
may result in overheating and battery case rupture.
Warning:
Do not attempt to disassemble, or incinerate any battery. Keep all batteries away from children. Dispose of used batteries promptly and as regulated by the
laws in your area. Note: Check with any retailer of household type batteries in your area for battery disposal information.
Disposal Notice:
Should this product become damaged beyond repair, or for some reason its useful life is considered to be at an end, please observe all local, state, and
federal regulations that relate to the disposal of products that contain lead, batteries, plastics, etc. If your dealer is unable to assist you, please contact Yamaha directly.
NAME PLATE LOCATIOIN: The name plate is located on the bottom of the product. The model number, serial number, power requirements, etc., are located on this plate.
You should record the model number, serial number, and the date of purchase in the spaces provided below and retain this manual as a permanent record of your purchase.
Model
Serial No.
Purchase Date
PLEASE KEEP THIS MANUAL
Use the supplied monaural phone cable to connect the pad's output jack to the DTX Series
Drum Trigger Module's Input (9/10, etc.) (DTXPRESS/DTX/DTXTREME).
Jack
Jack Cable
Pad
:
Never apply excessive force (pulling, bending, etc.) on the PCY10's jack and cable.
Also, never use the PCY10 when its jack and cable are not restrained. Doing so
may result in the wire breaking.
●
Using the PCY10 with the PCY60, 80,
65 Series Cymbal Pad (PCY60, 80/80S,
65/65S)
First, setup the rack system (Yamaha RS
Series, etc.) or a cymbal stand (Yamaha CS
Series, etc.) then use the supplied wing nut,
felt, etc., to attach the cymbal pad as shown
in the illustration.
The * denotes parts that are supplied with the PCY10.
●
Using the PCY10 alone
First, setup the rack system (Yamaha RS
Series, etc.) or a cymbal stand (Yamaha CS
Series, etc.) and attach in the same manner
as an acoustic cymbal.
Cymbal Support
* Small Felt
* Wing Nut
PCY10
* Large Felt
PCY60, 80, 65
Series Cymbal Pad
Felt
Stopper
(Supplied with
the PCY65S)
Felt
PCY10
Felt
Wing Nut
Jack
Phone Cable (supplied)
Wrap the cable band (supplied)
Rack system's pipe, etc.
■
Part Names
■
Connections
■
Setting Up
Adjusting the Voice Volume
To change the volume of the voice assigned to the PCY10, use the [VOICE] Edit Mode
in the DTX Series Drum Trigger Module. Please refer to the Owner's Manual that came
with your module for further information.
To keep the PCY10 from rotating, position the
Stopper's shaft between the two ribs located
on the underside of the PCY10.
Cymbal Support
●
Fastening the Jack
Use the supplied cable band to fasten the PCY10's jack to the rack system or cymbal
stand, as shown in the illustration below.
NOTE:
When a cable that can combine the input of two monaural sources into a stereo plug is used
(optional: Yamaha CO4Y, etc.), individual sounds can be assigned to separate pads (two PCY10s,
a PCY10 and a PCY65, etc.) in the DTX Series Drum Trigger Module. (Use the following inputs_
DTXPRESS: 9/10; DTX: 9/10, 11/12; DTXTREME: 9/10-15/16.) Please refer to the Owner's Manual
that came with your module for more information.
