background image

11

Specifications

General Specifications

PC9500N

PC4800N

120 V (US)/ 240 V (A) 230 V (EU)

120 V (US)/ 240 V (A)

230 V (EU)

Power Output Level (Rated Power) 8

/STEREO

1000 W x 2

1050 W x 2

550 W x 2

500 W x 2

1 kHz

4

/STEREO

1600 W x 2

1650 W x 2

850 W x 2

800 W x 2

THD+N= 1%

8

/BRIDGE

3200 W x 1

3300 W x 1

1700 W x 1

1600 W x 1

8

/STEREO

925 W x 2

950 W x 2

475 W x 2

450 W x 2

20 Hz–20 kHz

4

/STEREO

1400 W x 2

1500 W x 2

725 W x 2

700 W x 2

THD+N= 0.1%

8

/BRIDGE

2800 W x 1

3000 W x 1

1450 W x 1

1400 W x 1

1 kHz

2

/STEREO

2300 W x 2

2300 W x 2

1200 W x 2

1200 W x 2

20mS nonclip

4

/BRIDGE

4600 W x 1

4600 W x 1

2400 W x 1

2400 W x 1

Power Bandwidth

Half Power

10 Hz–40 kHz (THD+N= 0.5%)

Total Harmonic Distortion (THD + N)

20 Hz~20 kHz, Half Power

0.1%

Frequency Response

RL= 8

, Po= 1 W

0 dB, 0.5 dB, –1 dB     f=20 Hz–50 kHz

Intermodulation distortion (IMD)

60 Hz:7 kHz, 4:1, Half Power

0.1%

Channel Separation

Half Power, RL= 8

, 1 kHz

70 dB

Vol. max., input 600

 shunt

Residual Noise     Vol. min.

20 Hz~20 kHz (DIN AUDIO)

 –70 dB

SN Ratio

20 Hz~20 kHz (DIN AUDIO)

106 dB

103 dB

Damping Factor

RL=8

, f= 1 kHz

800

Sensitivity (Vol. max.) Rated Power into 8

+9 dB

+6 dB

Voltage Gain (Vol. max.)

32 dB

Input Impedance

30 k

/Balanced,  15 k

/Unbalanced

Controls

Front Panel

POWER switch (ON/OFF)
Volume (31 position) /ch

Rear Panel

MODE switch (STEREO/BRIDGE/PARALLEL)
HPFswitch (ON/OFF)  fc=40 Hz 12dB/octave
DIP switch (6P)

Connectors

Input

XLR-3-31 type/ch
Euroblock connector /ch

Output

SPEAKON /ch, 5-way binding posts

NETWORK

RJ45 x 2

POWER

AC INLET

Indicators

POWER/STAND-BY

Green/Orange

PROTECTION

Red

TEMP

Red (heatsink temp 

 85

°

C)

REMOTE

Green

Meters

10 points LED meter

Load protection

POWER switch ON muting, DC detection

Amp. protection

Temp. detection (heatsink temp 

 90

°

C), VI limiter (R

L

 

 1 

)

Limiter

Comp. : THD 

 0.5%

Cooling

Dual Variable-speed fan

Power Requirements

US & Canada

120 V, 60 Hz

Europe

230 V, 50/60 Hz

Other

240 V, 50/60 Hz

Power Consumption

Idling

55 W

40 W

Output power, 4

120 V 750 W   230 V 1100 W

120 V 450 W   230/240 V 600 W

240 V 1000 W

Dimensions (W x H x D)

480 x 88 x 456 mm

Weight

13 kg

12.5 kg

Accessories

Power cord, Security cover, Owner’s Manual, Euroblock connector (2)

0 dB=0.775 Vrms, Half Power=1/2 Power Output Level (Rated Power)
Specifications subject to change without notice.

For European Model
Purchaser/User information specified in EN55103-1 and EN55103-2.
Inrush Current: 20A (PC9500N) / 25A (PC4800N)
Conformed Environment: E1, E2, E3 and E4.

Содержание PC4800N

















Отзывы: