Yamaha MTN850-A 2017 Скачать руководство пользователя страница 134

Страница: 134 / 560

PERIODIC MAINTENANCE

3-24

production.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS30809

CHECKING THE CONNECTING ARM AND

RELAY ARM

Refer to “CHECKING THE CONNECTING ARM
AND RELAY ARM” on page 4-76.

EAS30656

CHECKING THE ENGINE OIL LEVEL

1. Stand the vehicle on a level surface.

TIP

•

Place the vehicle on a maintenance stand.

•

Make sure the vehicle is upright.

2. Start the engine, warm it up for several min-

utes, and then turn it off.

3. Check:

•

Engine oil level
The engine oil level should be between the
minimum level mark “a” and maximum level
mark “b”.
Below the minimum level mark



Add the

recommended engine oil to the proper level.

NOTICE

ECA13361

• Engine oil also lubricates the clutch and the

wrong oil types or additives could cause

clutch slippage. Therefore, do not add any

chemical additives or use engine oils with a

grade of “CD” or higher and do not use oils

labeled “ENERGY CONSERVING II”.

• Do not allow foreign materials to enter the

crankcase.

TIP

Before checking the engine oil level, wait a few
minutes until the oil has settled.

4. Start the engine, warm it up for several min-

utes, and then turn it off.

5. Check the engine oil level again.

TIP

Before checking the engine oil level, wait a few
minutes until the oil has settled.

EAS30657

CHANGING THE ENGINE OIL

1. Start the engine, warm it up for several min-

utes, and then turn it off.

2. Place a container under the engine oil drain

bolt.

3. Remove:

•

Engine oil filler cap “1”

•

Engine oil drain bolt “2”

•

Gasket “3”

Recommended brand

YAMALUBE

SAE viscosity grades

10W-40

Recommended engine oil grade

API service SG type or higher,

JASO standard MA

1 a

b
a

Содержание MTN850-A 2017

















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MTN850-A 2017

Отзывы:

Yamaha MTN850-A 2017, Руководство по обслуживанию, Страница: 134 / 560

Результаты поиска

Содержание MTN850-A 2017

Отзывы: