Yamaha MTN850-A 2017 Скачать руководство пользователя страница 221 | Manualshive

Страница: 221 / 560

Yamaha MTN850-A 2017 Скачать руководство пользователя страница 221

REAR SHOCK ABSORBER ASSEMBLY

4-76

EAS30826

HANDLING THE REAR SHOCK ABSORBER

WARNING

EWA13740

This rear shock absorber contains highly

compressed nitrogen gas. Before handling

the rear shock absorber, read and make sure

you understand the following information.

The manufacturer cannot be held responsi-

ble for property damage or personal injury

that may result from improper handling of

the rear shock absorber.

• Do not tamper or attempt to open the rear

shock absorber.

• Do not subject the rear shock absorber to

an open flame or any other source of high

heat. High heat can cause an explosion due

to excessive gas pressure.

• Do not deform or damage the rear shock

absorber in any way. Rear shock absorber

damage will result in poor damping perfor-

mance.

EAS30729

DISPOSING OF A REAR SHOCK ABSORBER

1. Gas pressure must be released before dis-

posing of a rear shock absorber. To release
the gas pressure, drill a 2–3 mm (0.08–0.12
in) hole through the rear shock absorber at a
point 20–25 mm (0.79–0.98 in) from its end
as shown.

WARNING

EWA13760

Wear eye protection to prevent eye damage

from released gas or metal chips.

EAS30219

REMOVING THE REAR SHOCK ABSORBER

ASSEMBLY

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is

no danger of it falling over.

TIP

Place the vehicle on a maintenance stand so
that the rear wheel is elevated.

2. Remove:

•

Connecting arm lower nut “1”

•

Connecting arm lower bolt

•

Relay arm nut “2”

•

Relay arm bolt

TIP

When removing the bolt, hold the swingarm so
that it does not drop down.

3. Remove:

•

Rear shock absorber assembly upper nut

•

Rear shock absorber assembly upper bolt

•

Rear shock absorber assembly

TIP

Remove the rear shock absorber assembly from
between the swingarm and frame.

EAS30220

CHECKING THE REAR SHOCK ABSORBER

ASSEMBLY

1. Check:

•

Rear shock absorber rod
Bends/damage



Replace the rear shock

absorber assembly.

•

Rear shock absorber assembly
Gas leaks/oil leaks



Replace the rear shock

absorber assembly.

•

Spring

•

Bushings
Damage/wear



Replace the rear shock ab-

sorber assembly.

•

Bolts
Bends/damage/wear



Replace.

EAS30221

CHECKING THE CONNECTING ARM AND

RELAY ARM

1. Check:

•

Connecting arms “1”

•

Relay arm “2”
Damage/wear



Replace.

20-25 mm

(0.79-0.98 in)

2

1

«
...
219
220
221
222
223
...
»

Содержание MTN850-A 2017

















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов