Yamaha MBK MW125 2014 Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 380

background image

PERIODIC MAINTENANCE

3-25

EAS30664

ADJUSTING THE HEADLIGHT BEAM

1. Adjust:

• Headlight beam (vertically)

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Turn the adjusting screw “1” in direction “a” or

“b”.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

2. Adjust:

• Headlight beam (horizontally)

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Turn the adjusting screws “1” in direction “a”

or “b”.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS30665

REPLACING THE HEADLIGHT BULB

1. Disconnect:

• Headlight coupler “1”

2. Remove:

• Headlight bulb cover “2”

3. Remove:

• Headlight bulb holder “1”
• Headlight bulb

WARNING

EWA13320

Since the headlight bulb gets extremely hot,
keep flammable products and your hands
away from the bulb until it has cooled down.

4. Install:

• Headlight bulb

Secure the new headlight bulb with the head-
light bulb holder.

NOTICE

ECA13690

Avoid touching the glass part of the head-
light bulb to keep it free from oil, otherwise
the transparency of the glass, the life of the
bulb and the luminous flux will be adversely
affected. If the headlight bulb gets soiled,
thoroughly clean it with a cloth moistened
with alcohol or lacquer thinner.

5. Install:

• Headlight bulb holder

6. Install:

• Headlight bulb cover

7. Connect:

• Headlight coupler

Direction “a”

Headlight beam is raised.

Direction “b”

Headlight beam is lowered.

Direction “a”

Headlight beam moves to the right.

Direction “b”

Headlight beam moves to the left.

b

a

b

a

1

b

a

b

a

1

2

1

1

New

«
...
104
105
106
107
108
...
»

Содержание MBK MW125 2014





























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MBK MW125 2014

Бренд: Honda Страницы: 112

Бренд: AFX Страницы: 52

Бренд: MadStad Engineering Страницы: 8

Бренд: hepco & becker Страницы: 4

690 Enduro R 2019

Бренд: KTM Страницы: 274

Бренд: Zontes Страницы: 119

Бренд: Dynafit Страницы: 20

DARK SMOKE SPORT

Бренд: Malossi Страницы: 4

Бренд: Dynajet Страницы: 20

Бренд: VESPA Страницы: 82

crivit sports 101545

Бренд: DELTA-SPORT Страницы: 42

Бренд: Cagiva Страницы: 136

Бренд: Cagiva Страницы: 162

Бренд: Malaguti Страницы: 121

Бренд: X-lite Страницы: 57

Бренд: RIEJU Страницы: 116

Бренд: KTM Страницы: 122

All New Classic 350

Бренд: Royal Enfield Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды