Yamaha M7CL-32, Руководство по обслуживанию

Страница: 138 / 375

M7CL-32/M7CL-48
138
(METER BRIDGE: Horizontal line lights downward.)
25. 12 point Meter 1 LED from MIX#1 to MATRIX#8 will light.
26. 12 point Meter 2 LED from MIX#1 to MATRIX#8 will light.
27. 12 point Meter 3 LED from MIX#1 to MATRIX#8 will light.
28. 12 point Meter 4 LED from MIX#1 to MATRIX#8 will light.
29. 12 point Meter 5 LED from MIX#1 to MATRIX#8 will light.
30. 12 point Meter 6 LED from MIX#1 to MATRIX#8 will light.
31. 12 point Meter 7 LED from MIX#1 to MATRIX#8 will light.
32. 12 point Meter 8 LED from MIX#1 to MATRIX#8 will light.
33. 12 point Meter 9 LED from MIX#1 to MATRIX#8 will light.
34. 12 point Meter 10 LED from MIX#1 to MATRIX#8 will light.
35. 12 point Meter 11 LED from MIX#1 to MATRIX#8 will light.
36. 12 point Meter 12 LED from MIX#1 to MATRIX#8 will light.
1-25 ETHERNET test
Contents: Judged as “OK” if connection to the PC is possible.
Example of executing screen
1.
Prepare the USB STORAGE and the environment with which
the data can be written and read (PC with USB).
2.
Copy the LPMO?_??.PGM and MPMO?_??.PGM files in
the CD to the root directory of the USB STORAGE.
3. Insert the USB storage to the USB and turn on the power.
4. When the confirmation message to execute the UPDATE is
displayed, press OK in the touch panel.
5. When the procedure is finished, check that the unit program
will automatically start and wait until the BUSY indicator
will be turned off. Then, turn off the power and remove the
USB storage.
After the program is updated and the power is turned on,
INITIALIZE screen will appear in CHECK SUM ERROR. Then,
execute the ALL INITIALIZE. Wait until the normal screen will
appear and BUSY indicator will be turned off. Then, turn off
the power.
2) For the CPUM Circuit Board
Insert the USB storage and turn on the power to update the
M7CL.
1.
Prepare the USB STORAGE and the environment with which
the data can be written and read (PC with USB).
2.
Copy the LPMO?_??.PGM and MPMO?_??.PGM files in
the CD to the root directory of the USB STORAGE.
3. Insert the USB storage to the USB IF attached to the MAIN
circuit board and turn on the power.
4.
Updating will be executed automatically and LED on the
circuit board will be turned off. Then, the uploading is finished.
5. Turn off the power and remove the USB.
3) For the CPUP Circuit Board
Same as the procedure on the MC7L.
4) Writing ETHER MAC Address and E-Serial
Write after checking the CPUM circuit borad.
Connect the M7CL to the PC through ETHER and write using
MAC Address writing software.
MAC address should be alternative and the write data should
not be copied.
5) INITIALIZE and CALIBRATION
Turn on while holding down the STORE button and the screen
for INITIALIZE and CALIBRATION will appear.
· INITIALIZATION
Refer to “Initializing the M7CL internal memory” (page 189).
· CALIBRATION
Refer to “Calibration” (page 191).
NG ETHERNET
NG:
NG Communication
AutoNext
OkData TxData
START PAUSE CLOSE
If the check result is NG
2. LOADING THE PROGRAM
2-1 How to check the version of the program
Press the SETUP button in function access area and SETUP
screen will appear, displaying the current firmware version.
CPUM/CPUP ....... The firmware versions of each CPU are
shown separately for “CPUM” (Main CPU)
and “CPUP” (CPU for screen control).
2-2 Updating the Program
1) M7CL
Usually, it is not necessary to upload as the program is already
written before assembly.
The uploading is necessary though in case of mismatch due to
version upgrading or the like.