BATTERY REPLACEMENT
Be sure to replace the battery as soon as possible when the battery check
indicator lights in order to avoid reduced sound quality.
* Be sure to remove the battery if the instrument will not be used for an
extended period of time in order to prevent possible damage due to
battery leakage.
THE CONTROLS
The output jack is an EIAJ-standard 1/4" phone jack. Be sure to use an
appropriate connection cable.
The built-in preamplifier is automatically turned on when a plug is
inserted into the output jack. When not using the instrument, or when
playing it without amplification, be sure to remove the plug from the
output jack so that the preamplifier power is turned off.
Always set the VOLUME control to “0” when plugging in or unplugging
the connection cable.
The battery check indicator (BATT.) will light briefly when a plug is
inserted or removed from the output jack. This is normal and does not
indicate a malfunction.
Be sure to remove the battery if the instrument will not be used for an
extended period of time in order to prevent possible damage due to
battery leakage.
PRECAUTIONS
ELECTRIC
ACOUSTIC GUITAR
Owner’s Manual
Thank you for choosing a Yamaha electric-acoustic guitar.
In order to make the most of the advanced features and
performance provided by your guitar, please read this
manual carefully before using the instrument.
SPECIFICATIONS
System
SYSTEM-45 (Monaural 2 way)
Pickup
• Bar Sensor (Piezo type)
• Condenser Mic (with gooseneck)
Pre-amplifier Controls
VOL., MIC.VOL., EQ control for bar sensor
(piezo) : HIGH, MID, LOW,
AMF, PHASE(Phase switch for mic)
Output jack
Combination end pin/power switch
Output impedance
1 k
Ω
Power supply
9V DC, S-006P (6F22) dry cell battery
Battery life
Approx. 350 hours
Accessories
• Hexagonal wrench for neck adjustment x1
• Sound hole cover for preventing feedback x1
• S-006P (6F22) dry cell battery x1
NOMENCLATURE
Battery Holder
Control Section
Output Jack (with power switch function)
Pickup
Bar Sensor
q
Press the catch on the battery holder in
the direction indicated by the arrow in the
illustration in order to unlock it.
w
Slide out the battery case.
Catch
Battery case
e
Remove the old battery from the battery
case, and insert the new battery making
sure that the (+) and (–) terminals of the
battery are positioned as shown in the
illustration. Use only a DC9V, S-006P
(6F22) or equivalent battery.
r
Slide the battery case back
into the battery holder and
press firmly so that the
battery case locks into
place.
DC9V
S-006P (6F22)
OPEN
OP
EN
OPEN
Pickup
Condenser Mic
CONDENSER MIC ADJUSTMENT
The condenser mic is attached inside the body (behind the preamplifier) with a
flexible pipe that allows free adjustment of the mic's direction.
A variety of tone variations are achievable by changing the direction of the mic head.
• When the guitar was shipped from the factory, the mic head is positioned inside
the body slightly pointed towards the sound hole and about 10mm from the
guitar's top. (You can see it from the sound hole.) This setting is good for picking
up the sound of the strings being plucked. (See diagram 1)
• When the mic head is slightly pointing toward the inside of the body this setting
will pickup a bigger body sound. (See diagram 2)
* Try some different mic placements and select the one you prefer.
Sound Hole Cover
(Accessory)
Feedback often occurs when controls are boosted on the electric acoustic guitar to
match the volume of other instruments when playing in a band.
Another source of feedback results from using the MIC. VOL. control to increase the
output from the internal condenser mic.
When the instrument is used under the conditions described above, the Sound Hole
Cover should be inserted into the sound hole.
With the Sound Hole Cover in place, feedback is effectively reduced.
USING THE SOUND HOLE COVER
(Diagram 1)
(Diagram 2)
Mic Head
Strings
10 mm
Toward the
c e n t e r o f
the body
A
M
F
q
w
e
r
t
y
LOW : Boosts or cuts the level of the low frequencies.
MID
: Boosts or cuts the level of the middle frequencies.
The AMF control
r
adjusts the center frequency of the band affected by
this control.
HIGH : Boosts or cuts the level of the high frequencies.
r
AMF Control
Sets the center frequency of the band of frequencies affected by the MID equalizer
control. The range is from 80 Hz to 10 kHz.
* This control has no effect when the MID equalizer control is set to its center (“0”)
position.
t
MIC. VOL.
Controls the volume of the condenser mic that is located inside the body (to the back
of the preamplifier).
* Setting the volume level too high may result in feedback causing damage to your
sound system. If feedback occurs, turn down the MIC. VOL. control until the feedback
stops or use a sound hole cover to prevent feedback.
y
PHASE switch for the MIC
Using this switch will change the tone when the mic signal is added to the guitar’s
tone. It can be effectively used to control feedback depending upon the devices that
are used and knob settings. Use it as you like.
q
VOL. (Volume) Control
Adjusts the overall output volume level.
* Make sure that the VOL. is turned to “0”
before connecting or disconnecting.
w
BATT. (Battery Check) Indicator
This indicator will light when the battery needs
to be replaced.
Please replace the battery as soon as
possible when the BATT. indicator lights.
e
Equalizer Controls for the Bar
Sensor (Piezo)
