Yamaha HTR-6080 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 125

background image

24

En

Connections

Both FM and AM indoor antennas are supplied with this
unit. Connect each antenna correctly to the designated
terminals. In general, these antennas should provide
sufficient signal strength.

y

See page 8 for connection information of the supplied indoor FM
antenna and AM loop antenna.

• The AM loop antenna should be placed away from this unit.
• The AM loop antenna should always be connected, even if an

outdoor AM antenna is connected to this unit.

• A properly installed outdoor antenna provides clearer reception

than an indoor one. If you experience poor reception quality,
install an outdoor antenna. Consult the nearest authorized
Yamaha dealer or service center about outdoor antennas.

■

AC OUTLETS (SWITCHED)

Use these 2 outlets to supply power to any connected
components. Connect the power cable of your other
components to these 2 outlets. Power to these 2 outlets is
supplied when this unit is turned on. However, power to
these 2 outlets is cut off when this unit is turned off. For
information on the maximum power or the total power
consumption of the components that can be connected to
these 2 outlets, see “Specifications” on page 106.

The power to AC OUTLETS of this unit is not cut off while this
unit is charging connected iPod even when this unit is in the
standby mode. When this unit completes charging or the iPod is
disconnected, the power is cut off automatically when this unit is
in the standby mode.

Connecting the FM and AM
antennas

Notes

ANTENNA

AM

FM

75

UNBAL.

GND

Indoor FM

antenna

(supplied)

Ground (GND terminal)

For maximum safety and minimum interference, connect the
antenna GND terminal to a good earth ground. A good earth
ground is a metal stake driven into moist earth.

AM loop
antenna
(supplied)

Outdoor AM antenna

Use a 5 to 10 m (16 to 33
ft) vinyl-covered wire
extended outdoors from a
window.

Connecting the power cable

Note

Memory back-up

The memory back-up circuit prevents the stored data
from being lost even if this unit is in the standby mode.
However, the stored data will be lost in case the power
cable is disconnected from the AC wall outlet or if the
power supply is cut off for more than one week.

AC OUTLETS

To the AC wall outlet

«
...
26
27
28
29
30
...
»

Содержание HTR-6080






























































































































Отзывы:

Нет отзывов

Похожие инструкции для HTR-6080

Бренд: Handic Страницы: 21

Бренд: FAAC Страницы: 2

Бренд: Yaesu Страницы: 63

Бренд: Yaesu Страницы: 80

Бренд: Duevi Страницы: 4

Sat-Light 7410F

Бренд: Foxcom Страницы: 74

Бренд: Rock Mars Страницы: 18

Бренд: Alpine Страницы: 36

Acrylic NO-SOLDER 40M Xceiver

Бренд: WA3RNC Страницы: 6

Бренд: Comba Telecom Страницы: 72

Бренд: HopeRF Страницы: 72

Бренд: D+M Group Страницы: 19

Бренд: Grundig Страницы: 6

Бренд: Strong Страницы: 35

Бренд: Yaesu Страницы: 17

PowerBox Cockpit

Бренд: PowerBox Systems Страницы: 30

Бренд: Chamberlain Страницы: 2

Бренд: Laird Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды