Yamaha GRIZZLY 350 YFM350AZ Скачать руководство пользователя | Manualshive

Страница: 108 / 138

background image

8-29

8

have the oil seals of the brake master cylinder and
calipers as well as the brake hoses replaced at the
intervals listed below or whenever they are dam-
aged or leaking.

●

Oil seals: Replace every two years.

●

Brake hoses: Replace every four years.

EBU24394

Checking the front brake lever free play

The brake lever free play must be checked at the
intervals specified in the periodic maintenance and
lubrication chart. The brake lever should have no
free play as shown. If there is free play, have a
Yamaha dealer check the brake system.

EBU24514

Adjusting the brake pedal and rear
brake lever free play and checking the
brake pedal position

The brake pedal and brake lever free play must be
checked and, if necessary, adjusted at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

TIP

●

Always perform this maintenance completely in
the following order whenever adjusting the rear
brake.

●

Before adjusting the brake lever and brake pedal
free play, check the rear brake shoes for wear.

Adjusting the brake pedal free play

The brake pedal free play should measure 20.0–
30.0 mm (0.79–1.18 in) as shown. If the free play
is incorrect, adjust it as follows.

1. No brake lever free play

U5WH66E0.book Page 29 Thursday, June 18, 2009 10:41 AM

«
...
106
107
108
109
110
...
»

Содержание GRIZZLY 350 YFM350AZ











































































































































Отзывы:

Нет отзывов

Похожие инструкции для GRIZZLY 350 YFM350AZ

WOLVERINE YFM45FXV

Бренд: Yamaha Страницы: 34

BLASTER YFS200S

Бренд: Yamaha Страницы: 46

Low Loader Trailer

Бренд: Futura Страницы: 20

650 MUD PRO 2011

Бренд: Arctic Cat Страницы: 84

Бренд: Taylor-Dunn Страницы: 136

BIG BEAR YFM400NN

Бренд: Yamaha Страницы: 161

BIG BEAR YFM400NC

Бренд: Yamaha Страницы: 162

BANSHEE YFZ350Y

Бренд: Yamaha Страницы: 142

Big Bear 400 YFM40FBB

Бренд: Yamaha Страницы: 156

Бренд: Yamaha Страницы: 156

BEARTRACKER YFM250XN

Бренд: Yamaha Страницы: 156

Бренд: Yamaha Страницы: 140

Бренд: Yamaha Страницы: 167

BIG BEAR YFM400FWS

Бренд: Yamaha Страницы: 173

BANSHEE 350 YFZ350Z

Бренд: Yamaha Страницы: 146

Бренд: Yamaha Страницы: 163

Бренд: Yamaha Страницы: 170

BANSHEE 350 YFZ350A

Бренд: Yamaha Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды