Yamaha GF12/12 Скачать руководство пользователя страница 21

Страница: 21 / 26

Specifications

—Owner’s Manual

Specifications

General specifications

• 0 dB is referenced to 0.775 Vrms.

Frequency response

20 Hz–20 kHz +1 dB, –3 dB @+4 dB into 600

Ω

(GROUP OUT, AUX OUT, ST OUT, MONO OUT)

Input gain control: minimum

Total harmonic distortion

Less than 0.1%, @20 Hz–20 kHz, +14 dB into 600

Ω

(GROUP OUT, AUX OUT, ST OUT, MONO OUT)

Hum & noise
(Average, Rs=150

Ω

with 20 Hz–20 kHz BPF)

–128 dB equivalent input noise

–95 dB residual output noise (GROUP OUT, AUX OUT, ST OUT, MONO OUT)

–86 dB
(GROUP OUT, ST OUT, MONO OUT)

Master fader: nominal level
All channel faders: minimum
All channel assign switches: off

–81 dB
(AUX OUT)

Master fader: nominal level
All channel faders, all AUX level controls:
minimum

–64 dB (68 dB S/N)
(GROUP OUT, AUX OUT, ST OUT)

Master fader, one channel fader, AUX level
control: nominal level, Assign switch: on
One channel gain control: maximum

Maximum voltage gain

84 dB CH IN to ST OUT
84 dB CH IN to GROUP OUT
58 dB ST IN to ST OUT
58 dB ST IN to GROUP OUT

Crosstalk
(at 1 kHz)

70 dB adjacent input
70 dB input to output

CH input gain control

44 dB variable

CH input PAD

0 dB/26 dB

CH input HPF

80 Hz 12 dB/oct

CH input equalization

15 dB maximum

HIGH

10 kHz

shelving*

MID

250 Hz–5 kHz peaking

LOW

100 Hz

shelving*

* Turn over/roll off frequency of shelving: 3 dB below maximum variable level.

ST input equalization

15 dB maximum

HIGH

10 kHz

shelving*

MID

2.5 kHz

peaking

LOW

100 Hz

shelving*

* Turn over/roll off frequency of shelving: 3 dB below maximum variable level.

Meters

13 points LED meters x4 (GROUP 1–4 /ST L R, PFL•AFL•TAPE IN L R)

CH peak indicators

Red LED on each channel turns on when Post EQ signal reaches the level –3 dB below clipping.

Phantom power

+48 V is supplied to electrically balanced inputs.

Power requirement

USA and Canada: 120 V AC 60 Hz
Other:

230 V AC 50 Hz

Power consumption

GF24/12: 70 W, GF16/12: 70 W, GF12/12: 70 W

Dimensions (WxHxD)

GF24/12: 938

157

487 mm

GF16/12: 701

157

487 mm

GF12/12: 587

157

487 mm

Weight

GF24/12: 20 kg, GF16/12: 16 kg, GF12/12: 14 kg

Содержание GF12/12



























Результаты поиска

Содержание GF12/12

Отзывы:

Похожие инструкции для GF12/12

Бренды по названию

Популярные бренды

Yamaha GF12/12, Руководство пользователя

Результаты поиска

Содержание GF12/12

Отзывы:

Похожие инструкции для GF12/12

Бренды по названию

Популярные бренды