Yamaha FZ6C Скачать руководство пользователя страница 78

Страница: 78 / 106

PERIODIC MAINTENANCE AND ADJUSTMENT

7-35

3. Place a new headlight bulb into po-

sition, and then secure it with the
bulb holder.

4. Install the headlight bulb cover,

and then connect the coupler.

5. Have a Yamaha dealer adjust the

headlight beam if necessary.

EAU32824

Replacing the tail/brake light
bulb

1. Remove the seat. (See page

4-14.)

2. Remove the socket (together with

the bulb) by turning it counter-
clockwise.

WARNING! Do not

touch the muffler bracket until
the exhaust system has cooled.

[EWA12302]

3. Remove the burnt-out bulb by

pushing it in and turning it counter-
clockwise.

4. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

5. Install the socket (together with the

bulb) by turning it clockwise.

6. Install the seat.

1. Headlight bulb holder

1. Tail/brake light bulb socket

2. Muffler bracket cover
3. Muffler bracket

U4S812E0.book Page 35 Monday, October 6, 2008 4:06 PM

Содержание FZ6C











































































































Результаты поиска

Содержание FZ6C

Отзывы:

Похожие инструкции для FZ6C

Бренды по названию

Популярные бренды

Yamaha FZ6C, Руководство пользователя

Результаты поиска

Содержание FZ6C

Отзывы:

Похожие инструкции для FZ6C

Бренды по названию

Популярные бренды