Yamaha FZ6-NV Скачать руководство пользователя

Страница: 70 / 90

PERIODIC MAINTENANCE AND MINOR REPAIR

6-30

EAU24202

Replacing a turn signal light
bulb

1. Remove the turn signal light lens

by removing the screw.

2. Remove the defective bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by installing the

screw.

CAUTION:

ECA11190

Do not overtighten the screw, other-
wise the lens may break.

EAU24310

Replacing the license plate
light bulb

1. Remove the license plate light unit

by removing the screws.

2. Remove the socket (together with

the bulb) by pulling it out.

3. Remove the defective bulb by pull-

ing it out.

4. Insert a new bulb into the socket.
5. Install the socket (together with the

bulb) by pushing it in.

6. Install the license plate light unit by

installing the screws.

1. Screw

2. License plate light unit

1. License plate light bulb
2. License plate light bulb socket

U1B322E0.book Page 30 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

Содержание FZ6-NV



























































































Результаты поиска

Содержание FZ6-NV

Отзывы:

Похожие инструкции для FZ6-NV

Бренды по названию

Популярные бренды

Yamaha FZ6-NV, Руководство пользователя

Результаты поиска

Содержание FZ6-NV

Отзывы:

Похожие инструкции для FZ6-NV

Бренды по названию

Популярные бренды