Yamaha FZ6-NA Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 92

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-23

6

4. If the drive chain slack is incorrect,

adjust it as follows.

EAU34361

To adjust the drive chain slack

1. Loosen the axle nut, then loosen

the locknut at each end of the
swingarm.

2. To tighten the drive chain, turn the

adjusting nut at each end of the
swingarm in direction (a). To loos-
en the drive chain, turn the adjust-
ing nut at each end of the
swingarm in direction (b), and then
push the rear wheel forward.

NOTE:

Using the alignment marks on each
side of the swingarm, make sure that
both adjusting nuts are in the same po-
sition for proper wheel alignment.

CAUTION:

ECA10570

Improper drive chain slack will over-
load the engine as well as other vital
parts of the motorcycle and can lead
to chain slippage or breakage. To
prevent this from occurring, keep
the drive chain slack within the
specified limits.

3. Tighten the locknuts, and then

tighten the axle nut to the specified
torque.

1. Drive chain slack

1. Axle nut

2. Drive chain slack adjusting nut
3. Locknut

4. Alignment marks

Tightening torques:

Locknut:

16 Nm (1.6 m·kgf, 11 ft·lbf)

Axle nut:

120 Nm (12.0 m·kgf, 85 ft·lbf)

U5S3E0E0.book Page 23 Tuesday, September 19, 2006 9:37 AM

«
...
62
63
64
65
66
...
»

Содержание FZ6-NA





























































































Отзывы:

Нет отзывов

Похожие инструкции для FZ6-NA

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 44

Venitex BARRIER

Бренд: DELTA PLUS Страницы: 2

Бренд: Yamaha Страницы: 287

Бренд: Yamaha Страницы: 109

Бренд: kellermann Страницы: 5

Бренд: hepco & becker Страницы: 2

Бренд: DYNATEK Страницы: 3

Бренд: DYNATEK Страницы: 8

Бренд: IBEX Страницы: 3

Бренд: BMS Страницы: 11

Бренд: Cagiva Страницы: 124

Element Ready TMS69BL14

Бренд: Rockford Fosgate Страницы: 8

Бренд: Petzl Страницы: 12

Бренд: Honda Страницы: 293

Бренд: Honda Страницы: 84

Бренд: Rothewald Страницы: 27

Бренд: Royal Enfield Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды