Yamaha FZ1-SW Скачать руководство пользователя

Страница: 60 / 98

PERIODIC MAINTENANCE AND MINOR REPAIR

6-13

5. Lift the front of the fuel tank, and

then tilt it back and away from the
air filter case. (Do not disconnect
the fuel hoses!)

WARNING

EWA10410

●

Make sure that the fuel tank is
well supported.

●

Do not tilt or pull the fuel tank
too much, otherwise the fuel
hoses may come loose, which
could cause fuel leakage.

6. Remove the air filter case cover by

removing the screws.

CAUTION:

ECA12880

When removing the air filter case
cover, be careful not to allow foreign
objects to drop into the air intake
manifold.

7. Pull the air filter element out.

8. Insert a new air filter element into

the air filter case.

CAUTION:

ECA10480

●

Make sure that the air filter ele-
ment is properly seated in the
air filter case.

●

The engine should never be op-
erated without the air filter ele-
ment installed, otherwise the
piston(s) and/or cylinder(s) may
become excessively worn.

9. Install the air filter case cover by in-

stalling the screws.

10. Place the fuel tank in the original

position, and then install the bolts.

1. Bolt

1. Screw

2. Air filter case cover

1. Air filter element
2. Air intake manifold

U3C321E0.book Page 13 Friday, September 29, 2006 4:57 PM

ProCarManuals.com

Содержание FZ1-SW



































































































Результаты поиска

Содержание FZ1-SW

Отзывы:

Похожие инструкции для FZ1-SW

Бренды по названию

Популярные бренды

Yamaha FZ1-SW, Руководство пользователя

Результаты поиска

Содержание FZ1-SW

Отзывы:

Похожие инструкции для FZ1-SW

Бренды по названию

Популярные бренды