manualshive.com logo in svg

Yamaha FL250A, Руководство пользователя

Поделиться
Скачать
Yamaha FL250A Скачать руководство пользователя страница 17

Specifications and requirements

10

Maximum output:

F200CET 147.1 kW@5500 r/min (200 
HP@5500 r/min)
F225BET 165.5 kW@5500 r/min (225 
HP@5500 r/min)
F225CET 165.5 kW@5500 r/min (225 
HP@5500 r/min)
F250AET 183.9 kW@5500 r/min (250 
HP@5500 r/min)
FL200CET 147.1 kW@5500 r/min (200 
HP@5500 r/min)
FL225BET 165.5 kW@5500 r/min (225 
HP@5500 r/min)
FL250AET 183.9 kW@5500 r/min (250 
HP@5500 r/min)

Idle speed (in neutral):

650 

±

50 r/min

Engine:

Type:

4-stroke V

Displacement:

3352.0 cm³

Bore 

×

 stroke:

94.0 

×

 80.5 mm (3.70 

×

 3.17 in)

Ignition system:

TCI

Spark plug (NGK):

LFR6A-11

Spark plug gap:

1.0–1.1 mm (0.039–0.043 in)

Control system:

Remote control

Starting system:

Electric starter

Starting carburetion system:

Electronic fuel injection

Valve clearance (cold engine) IN:

0.17–0.24 mm (0.0067–0.0094 in)

Valve clearance (cold engine) EX:

0.31–0.38 mm (0.0122–0.0150 in)

Min. cold cranking amps (CCA/EN):

711.0 A

Min. rated capacity (20HR/IEC):

100 Ah

Maximum generator output:

44 A

Drive unit:

Gear positions:

Forward-neutral-reverse

Gear ratio:

2.00(30/15)

Trim and tilt system:

Power trim and tilt

Propeller mark:

F200CET T / M
F225BET T / M
F225CET T / M
F250AET T / M
FL200CET TL / ML
FL225BET TL / ML
FL250AET TL / ML

Fuel and oil:

Recommended fuel:

F200CET Regular unleaded gasoline
F225BET Regular unleaded gasoline
F225CET Premium unleaded gasoline
F250AET Premium unleaded gasoline
FL200CET Regular unleaded gasoline
FL225BET Regular unleaded gasoline
FL250AET Premium unleaded gasoline

Min. research octane:

F200CET 90
F225BET 90
F225CET 94
F250AET 94
FL200CET 90
FL225BET 90
FL250AET 94

Recommended engine oil:

4-stroke outboard motor oil

U6P278E0.book  Page 10  Monday, April 11, 2011  7:37 PM

Содержание FL250A

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды