Yamaha FL150A страница 61 Скачать руководство пользователя | Manualshive

Страница: 61 / 90

background image

Operation

55

sure.

[EWM00262]

NOTICE:

Do not use the

tilt support lever or knob when traile-
ring the boat. The outboard motor
could shake loose from the tilt support
and fall. If the motor cannot be trail-
ered in the normal running position,
use an additional support device to
secure it in the tilt position. For more
detailed information, see page 58.

[ECM01641]

4.

Models equipped with trim rods: Once the
outboard motor is supported with the tilt
support lever, press the power trim and
tilt switch “

” (down) to retract the trim

rods.

NOTICE:

Make sure that the trim

rods retracts completely during moor-
ing. This protects the rods from ma-
rine growth and corrosion, which
could damage the power trim and tilt
mechanism.

[ECM00252]

EMU33121

Procedure for tilting down (power trim
and tilt models)

1.

Push the power trim and tilt switch “

”

(up) until the outboard motor is supported
by the tilt rod and the tilt support lever be-
comes free.

2.

Release the tilt support lever.

3.

Push the power trim and tilt switch “

”

(down) to lower the outboard motor to the
desired position.

DN

ZMU01936

UP

DN

ZMU04603

DN

U63P7AE0.book Page 55 Thursday, February 25, 2010 1:14 PM

«
...
59
60
61
62
63
...
»

Содержание FL150A



























































































Отзывы:

Нет отзывов

Похожие инструкции для FL150A

Бренд: Intel Страницы: 80

Бренд: Intel Страницы: 89

ML501MicroBlaze

Бренд: Xilinx Страницы: 46

Бренд: Texas Instruments Страницы: 25

Бренд: BCM Страницы: 93

Бренд: Gigabyte Страницы: 37

Бренд: MSI Страницы: 85

Бренд: ZiLOG Страницы: 42

Бренд: ON Semiconductor Страницы: 7

Бренд: Biostar Страницы: 32

Бренд: Systium Technologies Страницы: 4

Бренд: Foxconn Страницы: 75

Бренд: Semtech Страницы: 16

P35 NEO2-FR - Motherboard - ATX

Бренд: MSI Страницы: 9

TAS5001-5122C2EVM

Бренд: Texas Instruments Страницы: 27

Бренд: MSI Страницы: 148

Бренд: TYAN Страницы: 35

Бренд: TYAN Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды