Yamaha FL150A Скачать руководство пользователя | Manualshive

Страница: 60 / 90

background image

Operation

54

WARNING

EWM00250

Leaking fuel is a fire hazard. If there is a
fuel joint on the outboard motor, discon-
nect the fuel line or close the fuel cock if
the engine will be tilted for more than a few
minutes. Otherwise fuel may leak.

NOTICE

ECM00241

●

Before tilting the outboard motor, stop
the engine by following the procedure
on page 51. Never tilt the outboard mo-
tor while the engine is running. Severe
damage from overheating can result.

●

Do not tilt up the engine by pushing the
tiller handle (if equipped) because this
could break the handle.

EMU32724

Procedure for tilting up (power trim
and tilt models)

1.

Place the remote control lever in neutral.

2.

Press the power trim and tilt switch “

”

(up) until the outboard motor has tilted up
completely.

3.

Pull the tilt support lever toward you to
support the engine.

WARNING! After

tilting the outboard motor, be sure to
support it with the tilt support knob or
tilt support lever. Otherwise the out-
board motor could fall back down sud-
denly if oil in the power trim and tilt
unit or in the power tilt unit loses pres-

N

ZMU03196

N

ZMU04588

ZMU04602

UP

U63P7AE0.book Page 54 Thursday, February 25, 2010 1:14 PM

«
...
58
59
60
61
62
...
»

Содержание FL150A



























































































Отзывы:

Нет отзывов

Похожие инструкции для FL150A

Бренд: Balluff Страницы: 62

Бренд: Kaba Страницы: 16

Бренд: Faytech Страницы: 2

Бренд: DFI Страницы: 39

Бренд: Linear Страницы: 10

Бренд: ASROCK Страницы: 39

Бренд: Zotac Страницы: 54

Бренд: QDI Страницы: 85

Бренд: ST Страницы: 13

Бренд: austriamicrosystems Страницы: 19

tKINO-AL-E1-R10

Бренд: IEI Technology Страницы: 12

Бренд: ASROCK Страницы: 64

A320M PRO-VH PLUS

Бренд: MSI Страницы: 154

Бренд: ASROCK Страницы: 144

Бренд: HONDA marine Страницы: 2

Бренд: Commell Страницы: 29

Бренд: Intel Страницы: 87

Бренд: Intel Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды