Yamaha FL150A Скачать руководство пользователя | Manualshive

Страница: 32 / 90

background image

Instruments and indicators

26

EMU26524

Low oil pressure-alert indicator

If oil pressure drops too low, the alert indicator
will start to blink. For further information, see
page 37.

NOTICE

ECM00022

●

Do not continue to run the engine if the
low oil pressure-alert indicator is on and
the engine oil level is lower. Serious en-
gine damage will occur.

●

The low oil pressure-alert indicator does
not indicate the engine oil level. Use the
oil dipstick to check the remaining oil
quantity. For further information, see
page 43.

EMU26583

Overheat-alert indicator

If the engine temperature rises too high, the
alert indicator will start to blink. For further in-
formation on reading the indicator, see page
37.

NOTICE

ECM00052

Do not continue to run the engine if the
overheat-alert indicator is on. Serious en-
gine damage will occur.

EMU26602

Digital speedometer

This gauge shows the boat speed and other
information.

All segments of the display will light momen-
tarily after the main switch is turned on and
will return to normal thereafter.

EMU36061

Speedometer

The speedometer displays km/h, mph, or
knots, according to operator preference. Se-
lect the desired units of measurement by set-
ting the selector switch on the back of the
gauge. See the illustration for settings.

1. Low oil pressure-alert indicator

ZMU01736

1

1. Overheat-alert indicator

1. Speedometer
2. Fuel gauge

3. Trip meter/clock/voltmeter

4. Alert indicator(s)

ZMU01737

1

U63P7AE0.book Page 26 Thursday, February 25, 2010 1:14 PM

«
...
30
31
32
33
34
...
»

Содержание FL150A



























































































Отзывы:

Нет отзывов

Похожие инструкции для FL150A

Бренд: Ublox Страницы: 27

Бренд: AOpen Страницы: 8

Бренд: ASROCK Страницы: 6

PP-I7RS400 PURE PERFORMANCE II

Бренд: Sapphire Audio Страницы: 44

Бренд: National Semiconductor Страницы: 13

Бренд: Fastfame Страницы: 41

Бренд: LanParty Страницы: 141

Fatal1ty B150 Gaming K4

Бренд: ASROCK Страницы: 154

Бренд: ASROCK Страницы: 97

Бренд: Texas Instruments Страницы: 24

TLV320AIC12KEVM-K

Бренд: Texas Instruments Страницы: 40

Бренд: Fujitsu Siemens Computers Страницы: 24

Desktop Board D850EMD2

Бренд: Intel Страницы: 24

Бренд: Brother Страницы: 141

Бренд: Suzuki Страницы: 336

Бренд: SOYO Страницы: 3

Бренд: ASROCK Страницы: 69

Бренд: ASROCK Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды