background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-16

6

4. Add coolant or distilled water to

raise the coolant to the maximum
level mark, install the coolant res-
ervoir cap, the coolant reservoir
cap cover and the bolt.

CAUTION:

ECA10470

If coolant is not available, use
distilled water or soft tap water
instead. Do not use hard water
or salt water since it is harmful
to the engine.

If water has been used instead
of coolant, replace it with cool-
ant as soon as possible, other-
wise the engine may not be
sufficiently cooled and the cool-
ing system will not be protected
against frost and corrosion.

If water has been added to the
coolant, have a Yamaha dealer
check the antifreeze content of
the coolant as soon as possible,
otherwise the effectiveness of
the coolant will be reduced.

WARNING

EWA10380

Never attempt to remove the radiator
cap when the engine is hot.

NOTE:

The radiator fan is automatically
switched on or off according to the
coolant temperature in the radia-
tor.

If the engine overheats, see page
6-36 for further instructions.

EAU20470

Cleaning the air filter element 

The air filter element should be cleaned
at the intervals specified in the periodic
maintenance and lubrication chart.
Clean the air filter element more fre-
quently if you are riding in unusually
wet or dusty areas.

1. Remove panel E. (See page 6-8.)
2. Remove the intake air shroud by

removing the quick fastener
screws.

3. Remove the air filter case cover by

removing the screws.

1. Bolt
2. Coolant reservoir cap cover

3. Coolant reservoir cap

Coolant reservoir capacity (up to the 
maximum level mark):

0.25 L (0.26 US qt) (0.22 Imp.qt)

1. Intake air shroud

2. Quick fastener screw

5JW11.book  Page 16  Friday, May 9, 2003  4:03 PM

Содержание FJR1300(S)




































































































Отзывы: