Yamaha FAZER FZ6-SV 2006 Скачать руководство пользователя

Страница: 70 / 90

PERIODIC MAINTENANCE AND MINOR REPAIR

6-30

4. Install the headlight bulb cover,

and then connect the coupler.

5. Have a Yamaha dealer adjust the

headlight beam if necessary.

EAU32822

Replacing the tail/brake light
bulb

1. Remove the seat. (See page

3-13.)

2. Remove the socket (together with

the bulb) by turning it counter-
clockwise.

WARNING

EWA12301

Do not touch the muffler bracket un-
til the exhaust system has cooled.

3. Remove the defective bulb by

pushing it in and turning it counter-
clockwise.

4. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

5. Install the socket (together with the

bulb) by turning it clockwise.

6. Install the seat.

1. Tail/brake light bulb socket

2. Muffler bracket cover

U5VX22E0.book Page 30 Wednesday, September 14, 2005 11:42 AM

ProCarManuals.com

Содержание FAZER FZ6-SV 2006



























































































Результаты поиска

Содержание FAZER FZ6-SV 2006

Отзывы:

Похожие инструкции для FAZER FZ6-SV 2006

Бренды по названию

Популярные бренды

Yamaha FAZER FZ6-SV 2006, Руководство пользователя

Результаты поиска

Содержание FAZER FZ6-SV 2006

Отзывы:

Похожие инструкции для FAZER FZ6-SV 2006

Бренды по названию

Популярные бренды