Yamaha FAZER FZ6-SV 2006 Скачать руководство пользователя

Страница: 29 / 90

INSTRUMENT AND CONTROL FUNCTIONS

3-13

EAU32980

Seat

To remove the seat

1. Insert the key into the seat lock,

and then turn it counterclockwise.

2. While holding the key in that posi-

tion, lift the rear of the seat up, and
then pull the seat off.

To install the seat

1. Insert the projection on the front of

the seat into the seat holder as
shown.

2. Push the rear of the seat down to

lock it in place.

3. Remove the key.

NOTE:

Make sure that the seat is properly se-
cured before riding.

EAU14451

Storage compartment

The storage compartment is located
under the seat. (See page 3-13.)

WARNING

EWA10961

●

Do not exceed the load limit of 3
kg (7 lb) for the storage com-
partment.

●

Do not exceed the maximum
load of 190 kg (419 lb) for the ve-
hicle.

When storing the owner’s manual or
other documents in the storage com-
partment, be sure to wrap them in a
plastic bag so that they will not get wet.

1. Seat lock

2. Unlock.

1. Projection
2. Seat holder

1. Storage compartment

U5VX22E0.book Page 13 Wednesday, September 14, 2005 11:42 AM

ProCarManuals.com

Содержание FAZER FZ6-SV 2006



























































































Результаты поиска

Содержание FAZER FZ6-SV 2006

Отзывы:

Похожие инструкции для FAZER FZ6-SV 2006

Бренды по названию

Популярные бренды

Yamaha FAZER FZ6-SV 2006, Руководство пользователя

Результаты поиска

Содержание FAZER FZ6-SV 2006

Отзывы:

Похожие инструкции для FAZER FZ6-SV 2006

Бренды по названию

Популярные бренды