Yamaha FAZER FZ6-SV 2006 Скачать руководство пользователя | Manualshive

Страница: 69 / 90

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-29

6

EAU23740

Replacing the headlight bulb

This model is equipped with a quartz
bulb headlight. If the headlight bulb
burns out, replace it as follows.

1. Disconnect the headlight coupler,

and then remove the bulb cover.

2. Unhook the headlight bulb holder,

and then remove the defective
bulb.

WARNING

EWA10790

Headlight bulbs get very hot. There-
fore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooled
down.

3. Place a new headlight bulb into po-

sition, and then secure it with the
bulb holder.

CAUTION:

ECA10650

Take care not to damage the follow-
ing parts:

●

Headlight bulb
Do not touch the glass part of
the headlight bulb to keep it free
from oil, otherwise the transpar-
ency of the glass, the luminosity
of the bulb, and the bulb life will
be adversely affected. Thor-
oughly clean off any dirt and fin-
gerprints on the headlight bulb
using a cloth moistened with al-
cohol or thinner.

●

Headlight lens
Do not affix any type of tinted
film or stickers to the headlight
lens.
Do not use a headlight bulb of a
wattage higher than specified.

1. Headlight bulb cover

2. Headlight coupler

1. Headlight bulb holder

1. Do not touch the glass part of the bulb.

U5VX22E0.book Page 29 Wednesday, September 14, 2005 11:42 AM

ProCarManuals.com

«
...
67
68
69
70
71
...
»

Содержание FAZER FZ6-SV 2006



























































































Отзывы:

Нет отзывов

Похожие инструкции для FAZER FZ6-SV 2006

PAMPERA 400 - 2006

Бренд: GAS GAS Страницы: 70

Бренд: R&G Страницы: 6

Бренд: Nolan Страницы: 24

Бренд: X-lite Страницы: 136

Бренд: DUCATI Performance Страницы: 5

Бренд: DAELIM Страницы: 68

Бренд: RDMOTO Страницы: 2

Бренд: VEB Страницы: 63

Freeride 350 AUS

Бренд: KTM Страницы: 25

Бренд: CRATONI Страницы: 61

Бренд: Puch Страницы: 151

Бренд: TREND Страницы: 38

Бренд: RPS Страницы: 28

Бренд: kellermann Страницы: 7

Бренд: Salewa Страницы: 17

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 120

Бренд: Yamaha Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды