Yamaha F9.92D Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 92

background image

Important manual information

EMU25100

To the owner

Thank you for choosing a Yamaha outboard
motor. This Owner’s Manual contains infor-
mation needed for proper operation, mainte-
nance and care. A thorough understanding
of these simple instructions will help you ob-
tain maximum enjoyment from your new
Yamaha. If you have any question about the
operation or maintenance of your outboard
motor, please consult a Yamaha dealer.
In this Owner’s Manual particularly important
information is distinguished in the following
ways.

The Safety Alert Symbol means

ATTENTION! BECOME ALERT! YOUR
SAFETY IS INVOLVED!

WARNING

EWM00780

Failure to follow WARNING instructions
could result in severe injury or death to
the machine operator, a bystander, or a
person inspecting or repairing the out-

board motor.

CAUTION:

ECM00700

A CAUTION indicates special precautions
that must be taken to avoid damage to the

outboard motor.

NOTE:

A NOTE provides key information to make

procedures easier or clearer.

Yamaha continually seeks advancements in
product design and quality. Therefore, while
this manual contains the most current prod-
uct information available at the time of print-
ing, there may be minor discrepancies
between your machine and this manual. If
there is any question concerning this manu-

al, please consult your Yamaha dealer.

NOTE:

The F9.9MH, F9.9ER, T9.9ER, T9.9EH,
F15MH, F15EH, F15PR, F15PH and the
standard accessories are used as a base for
the explanations and illustrations in this
manual. Therefore some items may not ap-

ply to every model.

EMU25110

F9.92D, T9.92D, F15D

OWNER’S MANUAL

©2004 by Yamaha Motor Corporation, USA

1st edition, July 2004

All rights reserved.

Any reprinting or unauthorized use

without the written permission of

Yamaha Motor Corporation, USA

is expressly prohibited.

Printed in Japan

P/N LIT-18626-06-13

«
1
2
3
4
5
...
»

Содержание F9.92D





























































































Отзывы:

Нет отзывов

Похожие инструкции для F9.92D

Бренд: Gigabyte Страницы: 46

Бренд: TYAN Страницы: 117

Бренд: Biostar Страницы: 166

Бренд: Zamel Страницы: 2

Бренд: Gigabyte Страницы: 36

H55M-LE - - 01-2010

Бренд: ASROCK Страницы: 181

Бренд: Texas Instruments Страницы: 36

Бренд: Biostar Страницы: 115

Бренд: Biostar Страницы: 56

LCMXO3L-DSI-EVN

Бренд: Lattice Страницы: 2

Бренд: Avalue Technology Страницы: 29

Бренд: Gigabyte Страницы: 96

Бренд: Supermicro Страницы: 109

PROTO1 Xplained Pro

Бренд: Atmel Страницы: 17

Бренд: Supermicro Страницы: 127

Бренд: Gigabyte Страницы: 88

Бренд: ASROCK Страницы: 162

Бренд: Apex Digital Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды