Yamaha F9.9 страница 90 Скачать руководство пользователя | Manualshive

Страница: 90 / 112

background image

Maintenance

84

EMU29116

Inspecting wiring and connectors



Inspect that each connector is engaged se-
curely.



Inspect that each ground lead is properly
secured.

EMU32113

Checking propeller

WARNING

EWM01882

You could be seriously injured if the en-
gine accidentally starts when you are near
the propeller. Before inspecting, remov-
ing, or installing the propeller, place the
shift control in neutral, turn the main
switch to “

” (off) and remove the key,

and remove the clip from the engine shut-
off switch. Turn off the battery cut-off
switch if your boat has one.

Do not use your hand to hold the propeller
when loosening or tightening the propeller
nut. Put a wood block between the anti-cavi-
tation plate and the propeller to prevent the
propeller from turning.

Checkpoints



Check each of the propeller blades for ero-
sion from cavitation or ventilation, or other
damage.



Check the propeller shaft for damage.



Check the splines for wear or damage.



Check for fish line tangled around the pro-
peller shaft.



Check the propeller shaft oil seal for dam-
age.

EMU30663

Removing propeller

EMU29198

Spline models

1.

Straighten the cotter pin and pull it out
using a pair of pliers.

2.

Remove the propeller nut, washer, and
spacer (if equipped).

WARNING! Do not

use your hand to hold the propeller
when loosening the propeller nut.

[EWM01891]

ZMU07837

ZMU07969

ZMU07970

U6DR38E0.book Page 84 Tuesday, November 27, 2018 2:08 PM

©2020

Yamaha

Motor

Corporation

«
...
88
89
90
91
92
...
»

Содержание F9.9

















































































































Отзывы:

Нет отзывов

Похожие инструкции для F9.9

Бренд: Gan Systems Страницы: 24

Бренд: JETWAY Страницы: 48

Бренд: IEI Technology Страницы: 17

Бренд: Quick Страницы: 32

Бренд: JETWAY Страницы: 38

STEVAL-ISB042V1

Бренд: ST Страницы: 26

Бренд: Aaeon Страницы: 44

Бренд: MSI Страницы: 104

Бренд: Caji Страницы: 19

Бренд: Linear Страницы: 16

Fatal1ty B150 Gaming K4

Бренд: ASROCK Страницы: 154

Бренд: AOpen Страницы: 8

Бренд: Analog Devices Страницы: 7

dsPICDEM MCHV-3

Бренд: Microchip Technology Страницы: 68

Бренд: Texas Instruments Страницы: 28

Бренд: Sleipner Страницы: 24

Бренд: J&W Страницы: 39

PRO BTC+ Series

Бренд: ASROCK Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды