Yamaha F9.9 страница 102 Скачать руководство пользователя | Manualshive

Страница: 102 / 112

background image

Trouble Recovery

96



Avoid accidentally pulling the cord dur-
ing normal operation. Loss of engine
power means the loss of most steering
control. Also, without engine power, the
boat could slow rapidly. This could
cause people and objects in the boat to
be thrown forward.



Make sure no one is standing behind
you when pulling the starter rope. It
could whip behind you and injure some-
one.



An unguarded, rotating flywheel is very
dangerous. Keep loose clothing and
other objects away when starting the
engine. Use the emergency starter rope
only as instructed. Do not touch the fly-
wheel or other moving parts when the
engine is running. Do not install the
starter mechanism or top cowling after
the engine is running.



Do not touch the ignition coil, spark plug
wire, spark plug cap, or other electrical
components when starting or operating
the motor. You could get an electrical
shock.

EMU29563

Emergency starting engine

1.

Remove the top cowling.

2.

Remove the start-in-gear protection ca-
ble from the starter, if equipped.

3.

Remove the starter/flywheel cover after
removing the bolt(s).

4.

Prepare the engine for starting. For fur-
ther information, see page 48. Be sure
the engine is in neutral and that the clip is
attached to the engine shut-off switch.
The main switch must be “

” (on), if

equipped.

5.

If equipped the choke knob, pull out it
when the engine is cold. After the engine
starts, gradually return the choke knob to
its home position as the engine warms
up.

1. Start-in-gear protection cable

ON

OFF

ZMU01880

U6DR38E0.book Page 96 Tuesday, November 27, 2018 2:08 PM

©2020

Yamaha

Motor

Corporation

«
...
100
101
102
103
104
...
»

Содержание F9.9

















































































































Отзывы:

Нет отзывов

Похожие инструкции для F9.9

Бренд: Biostar Страницы: 47

Бренд: Gigabyte Страницы: 100

Бренд: J&W Страницы: 37

Бренд: ECS Страницы: 52

Бренд: Advantech Страницы: 118

Spacewalker AK32

Бренд: Shuttle Страницы: 89

Бренд: AKM Страницы: 30

Бренд: Arbor Technology Страницы: 86

Бренд: Gigabyte Страницы: 18

H55M-LE - - 01-2010

Бренд: ASROCK Страницы: 181

H470 AORUS PRO AX

Бренд: Gigabyte Страницы: 52

Бренд: ASROCK Страницы: 257

Бренд: Biostar Страницы: 56

Бренд: Gigabyte Страницы: 64

Бренд: Maxus Страницы: 59

Бренд: Fastrax Страницы: 12

Бренд: Gigabyte Страницы: 80

TAS5001-5122C2EVM

Бренд: Texas Instruments Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды