background image

Maintenance

67

11. Start the engine and make sure that the

low oil pressure-alert indicator remains
off. Also, make sure that there are no oil
leaks. 

NOTICE:

 If the low oil pressure-

alert indicator comes on or if there are
oil leaks, stop the engine and find the
cause. Continued operation with a
problem could cause severe engine
damage. Consult your Yamaha dealer
if the problem cannot be located and
corrected.

 [ECM01622]

12. Dispose of used oil according to local

regulations.

TIP:

For more information on the disposal of
used oil, consult your Yamaha dealer.

Change the oil more often when operating
the engine under adverse conditions such
as extended trolling.

EMU29112

Checking wiring and connectors

Check that each grounding wire is properly
secured.

Check that each connector is engaged se-
curely.

EMU32111

Checking propeller

WARNING

EWM01880

You could be seriously injured if the en-
gine accidentally starts when you are near
the propeller.

Before inspecting, removing, or install-
ing the propeller, place the shift control
in neutral, turn the main switch to “

(off) and remove the key, and remove
the clip from the engine shut-off switch.
Turn off the battery cut-off switch if your
boat has one.

Do not use your hand to hold the propeller
when loosening or tightening the propeller
nut. Put a wood block between the anti-cavi-
tation plate and the propeller to prevent the
propeller from turning.

Checkpoints

1. Lower level mark

2. Oil dipstick

3. Upper level mark

ZMU04243

ZMU01897

U6D625E0.book  Page 67  Thursday, March 13, 2008  9:06 AM

Содержание F75B

























































































Отзывы: