manualshive.com logo in svg

Yamaha F6D, Руководство пользователя

Поделиться
Скачать
Yamaha F6D Скачать руководство пользователя страница 21

Basic components

15

EMU25830

Fuel joint

This joint is used to connect the fuel line.

EMU25841

Fuel gauge

This gauge is located on either the fuel tank
cap or on the fuel joint base. It shows the ap-
proximate amount of fuel remaining in the
tank.

EMU25850

Fuel tank cap

This cap seals the fuel tank. When removed,
the tank can be filled with fuel. To remove the
cap, turn it counterclockwise.

EMU25860

Air vent screw

This screw is on the fuel tank cap. To loosen
the screw, turn it counterclockwise.

EMU26180

Remote control

The remote control lever actuates both the
shifter and the throttle. The electrical switches
are mounted on the remote control box.

EMU26190

Remote control lever

Moving the lever forward from the neutral po-
sition engages forward gear. Pulling the lever
back from neutral engages reverse. The en-
gine will continue to run at idle until the lever
is moved about 35° (a detent can be felt).
Moving the lever farther opens the throttle,
and the engine will begin to accelerate.

1. Air vent screw

2. Fuel gauge

3. Fuel joint

4. Fuel tank cap

ZMU01992

3

2

4

1

1. Power trim and tilt switch

2. Remote control lever

3. Neutral interlock trigger

4. Neutral throttle lever
5. Main switch / choke switch

6. Engine stop lanyard switch

7. Throttle friction adjuster

1. Neutral “ ”

2. Forward “ ”
3. Reverse “ ”

4. Shift

5. Fully closed
6. Throttle

7. Fully open

U60R10E0.book  Page 15  Monday, June 21, 2004  9:34 AM

Содержание F6D
























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды