Yamaha F50C Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 114

background image

2-11

E

001060

q

EMU01110

Low Oil Pressure Warning Indicator

If oil pressure drops too low, the warning
indicator will start to blink. Refer to the
section “LOW OIL PRESSURE WARNING”
for details.

1

Low oil pressure warning indicator

c

C

8

Do not operate the engine without oil.
Serious engine damage will occur.

8

The low oil pressure warning indicator
does not indicate the oil level in the
engine. Use the Oil Level Gauge to
check the remaining oil quantity. (Refer
to the section “CHECKING THE ENGINE
OIL LEVEL” for details.)

001061

q

EMU01553

Overheat Warning Indicator

If the engine temperature rises too high,
the warning indicator will start to blink.
Refer to “OVERHEAT WARNING” for
details.

1

Overheat warning indicator

c

C

Do not continue to operate the engine if a
warning device has activated. If neces-
sary, refer to the “TROUBLESHOOTING”
section in this manual. Consult your deal-
er if the problem cannot be located and
corrected.

62Y-9-1C-2 3/20/03 10:22 AM Page 12

«
...
32
33
34
35
36
...
»

Содержание F50C



















































































































Отзывы:

Нет отзывов

Похожие инструкции для F50C

Бренд: u-blox Страницы: 25

Бренд: NXP Semiconductors Страницы: 14

Бренд: QDI Страницы: 22

Бренд: Mercury Страницы: 41

Бренд: RAK Страницы: 17

EmbCore ROM-7421

Бренд: Advantech Страницы: 25

Бренд: A-Trend Страницы: 60

Motherboard DJ800

Бренд: IWILL Страницы: 52

Бренд: ASROCK Rack Страницы: 93

Бренд: Energy Страницы: 14

Бренд: AOpen Страницы: 8

BrillianX 1S/2000

Бренд: QDI Страницы: 63

Бренд: DFI Страницы: 115

Бренд: Supermicro Страницы: 93

Qseven conga-QA5

Бренд: Congatec Страницы: 61

Бренд: WinSystems Страницы: 16

Бренд: Intel Страницы: 29

Бренд: Gigabyte Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды