Yamaha F400A Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 106

background image

Trouble Recovery

91

EMU29435

Temporary action in emergen-

cy

EMU29442

Impact damage

EWM00871

The outboard motor can be seriously
damaged by a collision while operating or
trailering. Damage could make the out-
board motor unsafe to operate.

If the outboard motor hits an object in the wa-
ter, follow the procedure below.

(1) Stop the engine immediately.

(2) Check the control system and all compo-

nents for damage. Also, check the boat
for damage.

(3) Whether damage is found or not, return

to the nearest harbor slowly and careful-
ly.

(4) Have a Yamaha dealer check the out-

board motor before operating it again.

EMU35791

Running in an emergency (twin en-
gines or triple engines)

Normally use all outboard motors together for
cruising. When using only one or two engines
in an emergency, be sure to keep the unused
engine(s) tilted up and operate the other en-
gine(s) at low speed.

ECM01731

If the boat is operated with only one or two
engines, be sure to tilt the unused en-
gine(s) up. Otherwise water could enter
the exhaust pipe due to the wave action,
causing engine trouble.

Propeller shaft

Is propeller shaft damaged?

Have serviced by a Yamaha dealer.

Outboard motor
mounting

Are outboard motor mounting bolts
loose?

Tighten bolts or have serviced by a
Yamaha dealer.

Steering pivot

Is steering pivot loose or damaged?

Have serviced by a Yamaha dealer.

Trouble

The PTT TotalTilt function will not operate.

Item

Question

Answer

PTT TotalTilt func-
tion

Is the function deactivated?

Activate it.

PTT unit

Is the PTT unit stuck?

Clean the area around the PTT unit.

Buzzer

Is the buzzer malfunctioning?

Have serviced by a Yamaha dealer.

Tilt sensor

Is the tilt sensor malfunctioning?

Have serviced by a Yamaha dealer.

Trouble

Engine vibrates excessively.

Item

Question

Answer

U6KNK0E0.book Page 91 Monday, November 7, 2022 10:23 AM

«
...
95
96
97
98
99
...
»

Содержание F400A











































































































Отзывы:

Нет отзывов

Похожие инструкции для F400A

Бренд: RADWAG Страницы: 12

Бренд: Yamaha Страницы: 6

Бренд: Omega Страницы: 31

Бренд: E-Mon Страницы: 72

Бренд: Keller Страницы: 8

Бренд: Kawai Страницы: 110

Custom Reverb 18

Бренд: Olsson Страницы: 8

Бренд: Dadam micro Страницы: 24

Бренд: promesstec Страницы: 72

Бренд: Universal Laser Systems Страницы: 100

Бренд: Charder Страницы: 12

Celviano AP-60R

Бренд: Casio Страницы: 44

Бренд: YOKOGAWA Страницы: 123

Бренд: Technitone Страницы: 16

Бренд: ICP DAS USA Страницы: 340

ENERGY MAX EM400

Бренд: Molectron Страницы: 40

Бренд: Kawai Страницы: 10

Бренд: YUSHI Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды