Yamaha F400A Скачать руководство пользователя страница 61

Страница: 61 / 106

Operation

To release
(1) Place the control lever in “ ” (neutral).
(2) When the “CENTER ENGINE” switch is

pressed, a beep will sound and the LED
will go off.

EMU48720

Single lever switch operation

TIP:



When the single lever switch is activated,
the starboard control lever is inoperable.
You must start all the engines to enable the
single lever switch.

To set
(1) Place the control lever in “ ” (neutral).
(2) When the “SINGLE LEVER” switch is

pressed, a beep will sound and the LED
will come on.

(3) The port side control lever will allow you

to perform shift and throttle operations
for all outboard motors that have been
started.

To release
(1) Place the control lever in “ ” (neutral).
(2) When the “SINGLE LEVER” switch is

pressed, a beep will sound and the LED
will go off.

(3) You can perform normal shift or throttle

operations.

1. Port side control lever
2. Center engine

1. “SINGLE LEVER” switch
2. LED

1. Port side control lever
2. Port side engine
3. Center engine
4. Starboard side engine

U6KNK0E0.book Page 55 Monday, November 7, 2022 10:23 AM

Содержание F400A











































































































Результаты поиска

Содержание F400A

Отзывы:

Похожие инструкции для F400A

Бренды по названию

Популярные бренды

Yamaha F400A, Руководство пользователя

Результаты поиска

Содержание F400A

Отзывы:

Похожие инструкции для F400A

Бренды по названию

Популярные бренды