Yamaha F400A Скачать руководство пользователя страница 30

Страница: 30 / 106

Components

For multiple engine applications, the switch
on the control lever controls all outboard mo-
tors at the same time.

Single engine

Twin engines / Triple engines

EMU48491

DEC alert indicator

The alert indicator changes from blue to or-
ange if a connection problem between the di-
gital electronic control and the outboard

motor occurs. A beep also sounds (repeated-
ly on and off) to alert the operator. For more
information, consult your Yamaha dealer.

Single engine

Twin engines / Triple engines

EMU48503

Speed control switch

There are two modes for keeping the engine
speed and speed. Pressing the “

”

(up) /“

” (down) switch enables you to keep

the engine speed or to adjust the speed.

1. Power trim and tilt switch

1. Power trim and tilt switch (all engines)
2. Power trim and tilt switch (individual engine)

1. DEC alert indicator

U6KNK0E0.book Page 24 Monday, November 7, 2022 10:23 AM

Содержание F400A











































































































Результаты поиска

Содержание F400A

Отзывы:

Похожие инструкции для F400A

Бренды по названию

Популярные бренды

Yamaha F400A, Руководство пользователя

Результаты поиска

Содержание F400A

Отзывы:

Похожие инструкции для F400A

Бренды по названию

Популярные бренды