Yamaha F400A Скачать руководство пользователя страница 100

Страница: 100 / 106

Trouble Recovery

(2) Loosen the nut until it stops.

(3) To steer the outboard motor to the port

side, turn the lever counterclockwise. To
steer the outboard motor to the star-
board side, turn the lever clockwise.

EMU47611

Water separator-alert is activated af-
ter leaving port

EWM01501

Gasoline is highly flammable, and its va-
pors are flammable and explosive.



Do not perform this procedure on a hot
or running engine. Allow the engine to
cool.



There will be fuel in the fuel filter. Keep
away from sparks, cigarettes, flames or
other sources of ignition.



This procedure will allow some fuel to
spill. Catch fuel in a rag. Wipe up any
spilled fuel immediately.



The fuel filter must be reassembled
carefully with the O-ring, filter cup, and
hoses in place. Improper assembly or
replacement could result in a fuel leak,
which could result in a fire or explosion
hazard.

If the water separator-alert indicator blinks or
the buzzer sounds intermittently, perform the
following procedure.

1. Bolt
2. Clamp bracket cover

1. Nut

1. Lever

U6KNK0E0.book Page 94 Monday, November 7, 2022 10:23 AM

Содержание F400A











































































































Результаты поиска

Содержание F400A

Отзывы:

Похожие инструкции для F400A

Бренды по названию

Популярные бренды

Yamaha F400A, Руководство пользователя

Результаты поиска

Содержание F400A

Отзывы:

Похожие инструкции для F400A

Бренды по названию

Популярные бренды