Yamaha F25G Скачать руководство пользователя | Manualshive

Страница: 50 / 108

background image

Operation

44

battery connections are clean, secure and
covered by insulating covers. The electrical
connections of the battery and cables must
be clean and properly connected or the bat-
tery will not start the engine.
If the battery needs charging, consult your
Yamaha dealer or the battery manufacturer’s
instructions.

EMU2743A

Filling fuel

EWM01831



Gasoline and its vapors are highly flam-
mable and explosive. Always refuel ac-
cording to this procedure to reduce the
risk of fire and explosion.



Gasoline is poisonous and can cause
injury or death. Handle gasoline with
care. Never siphon gasoline by mouth.
If you should swallow some gasoline or
inhale a lot of gasoline vapor, or get
some gasoline in your eyes, see your
doctor immediately. If gasoline spills
on your skin, wash with soap and wa-
ter. If gasoline spills on your clothing,
change your clothes.

(1) Be sure the engine is stopped.
(2) Disconnect the fuel line from the fuel

tank and tighten the air vent screw on
the fuel tank cap.

(3) Remove the portable tank from the boat.
(4) Be sure you are in a well-ventilated out-

door area, either securely moored or
trailered.

(5) Do not smoke and keep away from

sparks, flames, static electric discharge,
or other sources of ignition.

(6) If you use a portable container to store

and dispense fuel, use only an approved
GASOLINE container.

(7) Touch the fuel nozzle to the filler open-

ing or funnel to help prevent electrostatic
sparks.

(8) Fill the fuel tank, but do not overfill.

WARNING! Do not overfill. Otherwise
fuel can expand and overflow if the
temperature increases.

[EWM02611]

(9) Tighten the filler cap securely.

ZMU06598

Fuel tank capacity:

24 L (6.34 US gal, 5.28 Imp.gal)

ZMU02301

ZMU02

83

4

6FM-28199-75-1E0.book 44 ページ２０１９年１０月３０日　水曜日　午前１１時２３分

«
...
48
49
50
51
52
...
»

Содержание F25G













































































































Отзывы:

Нет отзывов

Похожие инструкции для F25G

Бренд: Intel Страницы: 78

Бренд: Zapi Страницы: 50

Бренд: ZiLOG Страницы: 41

otometrics HI-PRO 2

Бренд: natus Страницы: 22

B550M AORUS PRO-P

Бренд: Gigabyte Страницы: 44

Бренд: VIA Technologies Страницы: 14

Бренд: ASROCK Страницы: 6

Бренд: JETWAY Страницы: 37

Бренд: Humandata Страницы: 10

K8T8AS - REV 3.0

Бренд: JETWAY Страницы: 26

Бренд: Bartels Mikrotechnik Страницы: 9

Бренд: Micronics Страницы: 63

Бренд: IEI Technology Страницы: 164

Бренд: JETWAY Страницы: 48

Бренд: Aaeon Страницы: 123

Бренд: Gigabyte Страницы: 41

Бренд: DFI Страницы: 48

Бренд: Supermicro Страницы: 99

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды