Yamaha F250 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 90

background image

Maintenance

47

EMU31480

Specifications

NOTE:

“(AL)” stated in the specification data below
represents the numerical value for the alumi-
num propeller installed.
Likewise, “(SUS)” represents the value for
stainless steel propeller installed and “(PL)”
for plastic propeller installed.

EMU28218

Dimension:

Overall length:

892 mm (35.1 in)

Overall width:

634 mm (25.0 in)

Overall height X:

1829 mm (72.0 in)

Overall height U:

1956 mm (77.0 in)

Transom height X:

643 mm (25.3 in)

Transom height U:

770 mm (30.3 in)

Weight (without propeller) X:

274.0 kg (604 lb)

Weight (without propeller) U:

280.0 kg (617 lb)

Performance:

Full throttle operating range:

5000–6000 r/min

Maximum output:

183.9 kW@5500 r/min (250 HP@5500 r/min)

Idling speed (in neutral):

650

±

50 r/min

Engine:

Type:

4-stroke V

Displacement:

3352.0 cm³ (204.54 cu.in)

Bore

×

stroke:

94.0

×

80.5 mm (3.70

×

3.17 in)

Ignition system:

TCI

Spark plug (NGK):

LFR6A-11

Spark plug gap:

1.0–1.1 mm (0.039–0.043 in)

Control system:

Remote control

Starting system:

Electric

Starting carburetion system:

Electronic fuel injection

Valve clearance (cold engine) IN:

0.17–0.23 mm (0.0067–0.0091 in)

Valve clearance (cold engine) EX:

0.31–0.37 mm (0.0122–0.0146 in)

Min. cold cranking amps (CCA/SAE):

512.0 A

Min. marine cranking amps (MCA/ABYC):

675.0 A

Min. reserve capacity (RC/SAE):

182 minutes

Alternator output for battery DC:

46.0 A

Drive unit:

Gear positions:

Forward-neutral-reverse

Gear ratio:

2.00 (30/15)

Trim and tilt system:

Power trim and tilt

Propeller mark:

F250TR T / M
LF250TR TL / ML

Fuel and oil:

Recommended fuel:

Premium unleaded gasoline

Min. pump octane:

89

Recommended engine oil:

4-stroke outboard motor oil

Engine oil grade API:

API SE, SF, SG, SH, SJ, SL

Engine oil type SAE:

SAE10W30 or SAE10W40

Lubrication:

Wet sump

Engine oil quantity (excluding oil filter):

5.6 L (5.92 US qt) (4.93 Imp.qt)

Recommended gear oil:

Hypoid gear oil SAE#90

U6P213E0.book Page 47 Thursday, March 9, 2006 10:20 AM

«
...
51
52
53
54
55
...
»

Содержание F250



























































































Отзывы:

Нет отзывов

Похожие инструкции для F250

Бренд: Aerovent Страницы: 16

Бренд: Doosan Страницы: 108

Бренд: CHERUBINI Страницы: 24

Бренд: Brother Страницы: 42

Бренд: SunStar Страницы: 86

Бренд: Briggs & Stratton Страницы: 60

Бренд: Beta Страницы: 76

Бренд: Honda Страницы: 59

Бренд: O.S. engine Страницы: 2

Бренд: O.S. engine Страницы: 4

Бренд: O.S. engine Страницы: 2

Бренд: O.S. engine Страницы: 4

Ultra Drive UN-99

Бренд: Bettcher Страницы: 29

Бренд: STEYR MOTORS Страницы: 329

Бренд: Cors-Air Страницы: 21

Бренд: Grundfos Страницы: 12

Nitro Star T-15

Бренд: HPI Racing Страницы: 4

Бренд: Stiga Страницы: 232

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды