manualshive.com logo in svg

Yamaha F225C, Руководство пользователя

Поделиться
Скачать
Yamaha F225C Скачать руководство пользователя страница 21

Specifications and requirements

15

EMU25280

One Star—Low Emission

The one-star label identifies engines that
meet the Air Resources Board’s 2001 ex-
haust emission standards. Engines meeting
these standards have 75% lower emissions
than conventional carbureted two-stroke en-
gines. These engines are equivalent to the
U.S. EPA’s 2006 standards for marine en-
gines.

EMU25290

Two Stars—Very Low Emission

The two-star label identifies engines that meet
the Air Resources Board’s 2004 exhaust
emission standards. Engines meeting these
standards have 20% lower emissions than
One Star-Low-Emission engines.

EMU25300

Three Stars—Ultra Low Emission

The three-star label identifies engines that
meet the Air Resources Board’s 2008 ex-
haust emission standards. Engines meeting
these standards have 65% lower emissions
than One Star-Low-Emission engines.

EMU33861

Four Stars—Super Ultra Low Emission

The four-star label identifies engines that
meet the Air Resources Board’s Sterndrive
and Inboard marine engine 2009 exhaust
emission standards. Personal Watercraft and
Outboard marine engines may also comply
with these standards. Engines meeting these
standards have 90% lower emissions than
One Star-Low-Emission engines.

ZMU01702

ZMU01703

ZMU01704

ZMU05663

U6P276E0.book  Page 15  Wednesday, April 1, 2009  9:44 AM

Содержание F225C





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды