background image

Instrument and control functions

6-27

6

EAU13213

Fuel

Make sure there is sufficient gasoline in
the tank.

WARNING

EWA10882

Gasoline and gasoline vapors are
extremely flammable. To avoid fires
and explosions and to reduce the
risk of injury when refueling, follow
these instructions.

1. Before refueling, turn off the en-

gine and be sure that no one is sit-
ting on the vehicle. Never refuel
while smoking, or while in the vi-
cinity of sparks, open flames, or
other sources of ignition such as
the pilot lights of water heaters
and clothes dryers.

2. Do not overfill the fuel tank. Stop

filling when the fuel reaches the
bottom of the filler tube. Because
fuel expands when it heats up,
heat from the engine or the sun
can cause fuel to spill out of the
fuel tank.

3. Wipe up any spilled fuel immedi-

ately. 

NOTICE:

 Immediately

wipe off spilled fuel with a clean,
dry, soft cloth, since fuel may
deteriorate painted surfaces or
plastic parts.

 [ECA10072]

4. Be sure to securely close the fuel

tank cap.

WARNING

EWA15152

Gasoline is poisonous and can
cause injury or death. Handle gaso-
line with care. Never siphon gasoline
by mouth. If you should swallow
some gasoline or inhale a lot of gas-
oline vapor, or get some gasoline in
your eyes, see your doctor immedi-

ately. If gasoline spills on your skin,
wash with soap and water. If gaso-
line spills on your clothing, change
your clothes.

EAUN0750

NOTICE

ECA11401

Use only unleaded gasoline. The use
of leaded gasoline will cause severe
damage to internal engine parts,
such as the valves and piston rings,
as well as to the exhaust system.

1. Fuel tank filler tube

2. Maximum fuel level

1

2

Recommended fuel:

Unleaded gasoline only

Fuel tank capacity:

13 L (3.4 US gal, 2.9 Imp.gal)

Содержание CZD250-A


































































































































Отзывы: