manualshive.com logo in svg

Yamaha CYGNUS RAY ZR 2022, Дополнительное руководство по обслуживанию

Поделиться
Скачать
Yamaha CYGNUS RAY ZR 2022 Скачать руководство пользователя страница 62

PERIODIC MAINTENANCE

3-1

CHK

ADJ

EAS20022

PERIODIC MAINTENANCE (For Drum)

EAS30022

INTRODUCTION

This chapter includes all information necessary to perform recommended checks and adjustments. If 
followed, these preventive maintenance procedures will ensure more reliable vehicle operation, a lon-
ger service life and reduce the need for costly overhaul work. This information applies to vehicles al-
ready in service as well as to new vehicles that are being prepared for sale. All service technicians 
should be familiar with this entire chapter.

EAUE0173

TIP

• From 19000 km (11800 mi), repeat the maintenance intervals starting from 4000 km (2400 mi).
• Items marked with an asterisk (*) should be performed by a Yamaha dealer as they require special 

tools, data and technical skills.

• Maintenance intervals marked with a double asterisk (**) would be paid service.

EAUE3710

PERIODIC MAINTENANCE CHART FOR THE EMISSION CONTROL SYSTEM

EAUE3721

GENERAL MAINTENANCE AND LUBRICATION CHART

NO.

ITEM

CHECK OR MAINTENANCE JOB

ODOMETER READING

1000 km 

(600 mi)

4000 km 

(2400 mi)

7000 km 

(4200 mi)

10000 km 

(6000 mi)

13000 km 

(7800 mi)

16000 km** 

(9600 mi)

1

*

Fuel line

• Check fuel hoses for cracks or 

damage.

• Replace if necessary.

2

*

Fuel filter

• Check condition.
• Replace if necessary.

Every 13000 km (7800 mi)

3

Spark plug

• Check condition.
• Clean and regap.

• Replace.

4

*

Valves

• Check valve clearance.
• Adjust if necessary.

Every 6000 km (3700 mi)

5

*

Fuel injection

• Check engine idle speed.

6

*

Exhaust system

• Check for leakage.
• Tighten if necessary.
• Replace gasket(s) if necessary.

7

*

Evaporative emis-
sion control system

• Check control system for dam-

age.

• Replace if necessary.

NO.

ITEM

CHECK OR MAINTENANCE JOB

ODOMETER READING

1000 km 

(600 mi)

4000 km 

(2400 mi)

7000 km 

(4200 mi)

10000 km 

(6000 mi)

13000 km 

(7800 mi)

16000 km** 

(9600 mi)

1

Diagnostic system 
check

• Perform dynamic inspection using 

Yamaha diagnostic tool.

• Check the error codes.

2

Air filter element

• Check.

• Replace.

Every 16000 km (9600 mi)

3

Sub air filter ele-
ment

• Clean.

4

Air filter case check 
hose

• Clean.

5

*

Battery 

• Check voltage.
• Charge if necessary.

6

*

Cogged belt case 
air filter element

• Clean.
• Replace if necessary.

B2UF8197E1.book  Page 1  Wednesday, October 6, 2021  4:38 PM

Содержание CYGNUS RAY ZR 2022




































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды