Yamaha BRUIN 350 Скачать руководство пользователя страница 50

Страница: 50 / 174

5-8

EBU00157

Tires

WARNING

POTENTIAL HAZARD

Operating this ATV with improper tires,
or with improper or uneven tire pres-
sure.

WHAT CAN HAPPEN

Use of improper tires on this ATV, or op-
eration of this ATV with improper or un-
even tire pressure, may cause loss of
control, increasing your risk of acci-
dent.

HOW TO AVOID THE HAZARD

1. The tires listed below have been ap-

proved by Yamaha Motor Co., Ltd.
for this model. Other tire combina-
tions are not recommended.

ACE-01E

Manufacturer

Size

Type

Front

MAXXIS

AT25

8-12

M911Y

Rear

MAXXIS

AT25

10-12

M912Y

2. The tires should be set to the rec-

ommended pressure:

●

Recommended tire pressure

Front 25 kPa (0.25 kgf/cm

, 3.6 psi)

Rear 25 kPa (0.25 kgf/cm

, 3.6 psi)

●

Check and adjust tire pressures when
the tires are cold.

●

Tire pressures must be equal on both
sides.

3. Tire pressure below the minimum

specified could cause the tire to
dislodge from the rim under severe
riding conditions.
The following are minimums:

Front 22 kPa (0.22 kgf/cm

, 3.2 psi)

Rear 22 kPa (0.22 kgf/cm

, 3.2 psi)

U5UH10.book Page 8 Monday, July 28, 2003 5:15 PM

Содержание BRUIN 350















































































































































































Результаты поиска

Содержание BRUIN 350

Отзывы:

Похожие инструкции для BRUIN 350

Бренды по названию

Популярные бренды

Yamaha BRUIN 350, Руководство пользователя

Результаты поиска

Содержание BRUIN 350

Отзывы:

Похожие инструкции для BRUIN 350

Бренды по названию

Популярные бренды