Yamaha 9.9F Скачать руководство пользователя | Manualshive

Страница: 31 / 62

background image

Operation

26

If equipped with a portable fuel tank
1.

Pour oil into the portable fuel tank, and
then add gasoline.

2.

Replace the fuel tank cap and close tight-
ly.

3.

Shake the fuel tank to mix the fuel thor-
oughly.

4.

Make sure that the oil and gasoline are
mixed.

If equipped with a built-in fuel tank
1.

Pour oil into a clean fuel can, and then
add gasoline.

2.

Replace the fuel can cap and close tight-
ly.

3.

Shake the fuel can to mix the fuel thor-
oughly.

4.

Make sure that the oil and gasoline are
mixed.

5.

Pour the gasoline and oil mixture into the
built-in fuel tank.

TIP:

If using a permanently installed tank, pour the
oil gradually as the gasoline is being added to
the tank.

EMU27452

Operating engine

WARNING

EWM00420

●

Before starting the engine, make sure
that the boat is tightly moored and that
you can steer clear of any obstructions.
Be sure there are no swimmers in the
water near you.

●

When the air vent screw is loosened,
gasoline vapor will be released. Gaso-
line is highly flammable, and its vapors
are flammable and explosive. Refrain
from smoking, and keep away from
open flames and sparks while loosening
the air vent screw.

●

This product emits exhaust gases which
contain carbon monoxide, a colorless,
odorless gas which could cause brain
damage or death when inhaled. Symp-
toms include nausea, dizziness, and
drowsiness. Keep cockpit and cabin ar-
eas well ventilated. Avoid blocking ex-
haust outlets.

1.

: Gasoline

2.

: Engine oil

1. Engine oil
2. Gasoline

100:1

1 L

(0.26 US gal,

0.22 Imp gal)

12 L

(3.2 US gal,

2.6 Imp gal)

14 L

(3.7 US gal,

3.1 Imp gal)

24 L

(6.3 US gal,

5.3 Imp gal)

0.01 L

(0.01 US qt,

0.01 Imp qt)

0.12 L

(0.13 US qt,

0.11 Imp qt)

0.14 L

(0.15 US qt,

0.12 Imp qt)

0.24 L

(0.25 US qt,

0.21 Imp qt)

ZMU04910

U63V2DE0.book Page 26 Monday, February 22, 2010 9:00 AM

«
...
29
30
31
32
33
...
»

Содержание 9.9F































































Отзывы:

Нет отзывов

Похожие инструкции для 9.9F

Бренд: u-blox Страницы: 25

Бренд: Actel Страницы: 2

ADSP-BF518F EZ-Board

Бренд: Analog Devices Страницы: 111

Бренд: Biostar Страницы: 47

Бренд: Intel Страницы: 76

Бренд: Supermicro Страницы: 90

Бренд: BESTEK Страницы: 52

Бренд: Zida Страницы: 28

Бренд: VIA Technologies Страницы: 76

Бренд: Supero Страницы: 101

EVAL-6ED100HPDRIVE-AS

Бренд: Infineon Страницы: 14

K8T8AS - REV 3.0

Бренд: JETWAY Страницы: 26

Бренд: JETWAY Страницы: 48

Бренд: Digilent Страницы: 23

Бренд: Bartels Mikrotechnik Страницы: 9

VVDI Mini Key Tool

Бренд: Xhorse Страницы: 17

Бренд: Mercury Страницы: 57

Бренд: Maxus Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды