Yamaha 40C Скачать руководство пользователя

Страница: 95 / 114

5-4

Trouble

Possible Cause

Remedy

13. Poor connections or damaged

ignition wiring.

14. Failed ignition parts.

15. Specified engine oil not used.

16. Thermostat faulty or clogged.

17. Air vent screw closed.

18. Fuel pump damaged.

19. Fuel joint connection incorrect.

20. Heat range of spark plug incorrect.

13. Check wires for wear or breaks.

Tighten all loose connections.

Replace worn or broken wires.

14. Have serviced by a Yamaha

dealer.

15. Check and replace oil with

specified type.

16. Have serviced by a Yamaha

dealer.

17. Open the air vent screw.

18. Have serviced by a Yamaha

dealer.

19. Connect correctly.

20. Inspect spark plug and replace it

with recommended type.

E. Engine power loss.

F. Engine vibrates

excessively.

1. Propeller damaged.

2. Propeller shaft damaged.

3. Weeds or other foreign matter

tangled on propeller.

4. Motor mounting bolt loose.

5. Steering pivot loose or damaged.

1. Have propeller repaired or

replaced.

2. Have serviced by a Yamaha

dealer.

3. Remove and clean propeller.

4. Tighten bolt.

5. Tighten or have serviced by a

Yamaha dealer.

63B-9-1B-5 2/27/03 3:39 PM Page 5

Содержание 40C



















































































































Результаты поиска

Содержание 40C

Отзывы:

Похожие инструкции для 40C

Бренды по названию

Популярные бренды

Yamaha 40C, Руководство пользователя

Результаты поиска

Содержание 40C

Отзывы:

Похожие инструкции для 40C

Бренды по названию

Популярные бренды