Yamaha 2009 XV250Y Скачать руководство пользователя

Страница: 68 / 84

PERIODIC MAINTENANCE AND ADJUSTMENT

7-33

3. Insert the wheel axle.
4. Lower the front wheel so that it is

on the ground.

5. Tighten the wheel axle to the spec-

ified torque.

6. Tighten the front wheel axle pinch

bolt to the specified torque.

7. While applying the front brake,

push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.

8. Connect the speedometer cable.

EAU25080

Rear wheel

EAU32751

To remove the rear wheel

WARNING

EWA10821

To avoid injury, securely support the
vehicle so there is no danger of it
falling over.

1. Remove the axle nut cotter pin.
2. Loosen the chain puller locknut

and the drive chain slack adjusting
nut on both ends of the swingarm.

1. Speedometer gear unit
2. Retainer

3. Speedometer cable

Tightening torque:

Wheel axle:

59 Nm (5.9 m·kgf, 43 ft·lbf)

Tightening torque:

Front wheel axle pinch bolt:

20 Nm (2.0 m·kgf, 14 ft·lbf)

1. Axle nut

2. Axle nut cotter pin

3. Chain puller locknut
4. Drive chain slack adjusting nut

5. Alignment marks

U2UJ26E0.book Page 33 Thursday, May 22, 2008 10:21 AM

Содержание 2009 XV250Y





















































































Результаты поиска

Содержание 2009 XV250Y

Отзывы:

Похожие инструкции для 2009 XV250Y

Бренды по названию

Популярные бренды

Yamaha 2009 XV250Y, Руководство пользователя

Результаты поиска

Содержание 2009 XV250Y

Отзывы:

Похожие инструкции для 2009 XV250Y

Бренды по названию

Популярные бренды