manualshive.com logo in svg

Yamaha 2008 YZF-R6X, Руководство по обслуживанию

Поделиться
Скачать
Yamaha 2008 YZF-R6X Скачать руководство пользователя страница 275

CRANKSHAFT

5-66

EAS26040

REMOVING THE CRANKSHAFT JOURNAL 
BEARINGS

1. Remove:

• Crankshaft journal lower bearings

(from the lower crankcase)

• Crankshaft journal upper bearings

(from the upper crankcase)

NOTE:

Identify the position of each crankshaft journal 
bearing so that it can be reinstalled in its origi-
nal place.

ET2C01018

CHECKING THE OIL NOZZLES

The following procedure applies to all of the oil 
nozzles.
1. Check:

• Oil nozzle

Damage/wear 

→

 Replace the oil nozzle.

• O-ring

Damage/wear 

→

 Replace.

• Oil passage

Obstruction 

→

 Blow out with compressed 

air.

EAS26070

CHECKING THE CRANKSHAFT AND CON-
NECTING RODS

1. Measure:

• Crankshaft runout

Out of specification 

→

 Replace the crank-

shaft.

2. Check:

• Crankshaft journal surfaces
• Crankshaft pin surfaces
• Bearing surfaces

Scratches/wear 

→

 Replace the crank-

shaft.

3. Measure:

• Crankshaft-journal-to-crankshaft-journal-

bearing clearance
Out of specification 

→

 Replace the crank-

shaft journal bearings.

CAUTION:

ECA13920

Do not interchange the crankshaft journal 
bearings. To obtain the correct crankshaft-
journal-to-crankshaft-journal-bearing clear-
ance and prevent engine damage, the 
crankshaft journal bearings must be 
installed in their original positions.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Clean the crankshaft journal bearings, 

crankshaft journals, and bearing portions of 
the crankcase.

b. Place the upper crankcase upside down on 

a bench.

c. Install the crankshaft journal upper bear-

ings “1” and the crankshaft into the upper 
crankcase.

NOTE:

Align the projections “a” on the crankshaft jour-
nal upper bearings with the notches “b” in the 
upper crankcase.

d. Put a piece of Plastigauge

®

 “1” on each 

crankshaft journal.

NOTE:

Do not put the Plastigauge

®

 over the oil hole in 

the crankshaft journal.

Runout limit C

0.030 mm (0.0012 in)

Journal oil clearance (using

plastigauge

®

)

0.020–0.044 mm (0.0008–
0.0017 in)

Содержание 2008 YZF-R6X



















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды