Yamaha 2008 YZF-R1X Скачать руководство пользователя | Manualshive

Страница: 71 / 108

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-22

6

WARNING

EWA10600

This motorcycle is fitted with super-
high-speed tires. Note the following
points in order to make the most ef-
ficient use of these tires.

●

Use only the specified replace-
ment tires. Other tires may run
the danger of bursting at super
high speeds.

●

Brand-new tires can have a rela-
tively poor grip on certain road
surfaces until they have been
“broken in”. Therefore, it is ad-
visable before doing any high-
speed riding to ride conserva-
tively for approximately 100 km
(60 mi) after installing a new tire.

●

The tires must be warmed up
before a high-speed run.

●

Always adjust the tire air pres-
sure according to the operating
conditions.

EAU21960

Cast wheels

To maximize the performance, durabil-
ity, and safe operation of your vehicle,
note the following points regarding the
specified wheels.

●

The wheel rims should be checked
for cracks, bends or warpage be-
fore each ride. If any damage is
found, have a Yamaha dealer re-
place the wheel. Do not attempt
even the smallest repair to the
wheel. A deformed or cracked
wheel must be replaced.

●

The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.

●

Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for it
to develop its optimal characteris-
tics.

EAU33890

Adjusting the clutch lever free
play

The clutch lever free play should mea-
sure 10.0–15.0 mm (0.39–0.59 in) as
shown. Periodically check the clutch le-
ver free play and, if necessary, adjust it
as follows.
To increase the clutch lever free play,
turn the adjusting bolt at the clutch lever
in direction (a). To decrease the clutch
lever free play, turn the adjusting bolt in
direction (b).

1. Clutch lever free play adjusting bolt

2. Clutch lever free play

U4C821E0.book Page 22 Tuesday, July 17, 2007 11:37 AM

«
...
69
70
71
72
73
...
»

Содержание 2008 YZF-R1X













































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008 YZF-R1X

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 44

Бренд: Honda Страницы: 118

Бренд: hepco & becker Страницы: 6

Бренд: hepco & becker Страницы: 5

Бренд: KEEWAY Страницы: 15

Бренд: RDMOTO Страницы: 2

VIKING 3250D FGS

Бренд: Lincoln Electric Страницы: 56

Бренд: HERO Страницы: 68

Бренд: Yamaha Страницы: 276

Бренд: Brixton Страницы: 49

Бренд: Athena Страницы: 88

Бренд: R&G Страницы: 6

Бренд: R&G Страницы: 6

Бренд: R&G Страницы: 6

Бренд: R&G Страницы: 9

Бренд: R&G Страницы: 22

Бренд: R&G Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды