Yamaha 2008 YZF-R1X Скачать руководство пользователя | Manualshive

Страница: 41 / 108

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-25

3

EAU15301

Sidestand

The sidestand is located on the left side
of the frame. Raise the sidestand or
lower it with your foot while holding the
vehicle upright.

NOTE:

The built-in sidestand switch is part of
the ignition circuit cut-off system, which
cuts the ignition in certain situations.
(See further down for an explanation of
the ignition circuit cut-off system.)

WARNING

EWA10240

The vehicle must not be ridden with
the sidestand down, or if the side-
stand cannot be properly moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
Yamaha’s ignition circuit cut-off
system has been designed to assist
the operator in fulfilling the respon-
sibility of raising the sidestand be-
fore starting off. Therefore, check
this system regularly as described

below and have a Yamaha dealer re-
pair it if it does not function proper-
ly.

EAU15312

Ignition circuit cut-off system

The ignition circuit cut-off system (com-
prising the sidestand switch, clutch
switch and neutral switch) has the fol-
lowing functions.

●

It prevents starting when the trans-
mission is in gear and the side-
stand is up, but the clutch lever is
not pulled.

●

It prevents starting when the trans-
mission is in gear and the clutch le-
ver is pulled, but the sidestand is
still down.

●

It cuts the running engine when the
transmission is in gear and the sid-
estand is moved down.

Periodically check the operation of the
ignition circuit cut-off system according
to the following procedure.

WARNING

EWA10250

If a malfunction is noted, have a
Yamaha dealer check the system be-
fore riding.

U4C821E0.book Page 25 Tuesday, July 17, 2007 11:37 AM

«
...
39
40
41
42
43
...
»

Содержание 2008 YZF-R1X













































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008 YZF-R1X

Бренд: Öhlins Страницы: 2

Mechatronics 35007-01

Бренд: Öhlins Страницы: 4

McPherson Strut MIR 5H02

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 4

Бренд: hepco & becker Страницы: 6

ST400 Cruiser Edition

Бренд: STEEL HORSE AUDIO Страницы: 6

Бренд: OKBABY Страницы: 35

Stelvio 1200 MY11 2011

Бренд: MOTO GUZZI Страницы: 385

Бренд: hepco & becker Страницы: 4

Бренд: Honda Страницы: 127

Бренд: A.J.S. Страницы: 94

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 116

Tracer 9 GT 2021

Бренд: Yamaha Страницы: 126

Бренд: Yamaha Страницы: 116

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 116

Бренд: Yamaha Страницы: 87

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды