background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-32

6

3. Remove the defective bulb by

pushing it in and turning it counter-
clockwise.

4. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

5. Install the socket (together with the

bulb) by pushing it in and turning it
clockwise until it stops.

6. Install the headlight unit by install-

ing the screws.

EAU24350

Supporting the motorcycle 

Since this model is not equipped with a
centerstand, follow these precautions
when removing the front and rear
wheel or performing other maintenance
requiring the motorcycle to stand up-
right. Check that the motorcycle is in a
stable and level position before starting
any maintenance. A strong wooden
box can be placed under the engine for
added stability.

To service the front wheel

1. Stabilize the rear of the motorcycle

by using a motorcycle stand or, if
an additional motorcycle stand is
not available, by placing a jack un-
der the frame in front of the rear
wheel.

2. Raise the front wheel off the

ground by using a motorcycle
stand.

To service the rear wheel

Raise the rear wheel off the ground by
using a motorcycle stand or, if a motor-
cycle stand is not available, by placing

a jack either under each side of the
frame in front of the rear wheel or under
each side of the swingarm.

1. Auxiliary light bulb socket

U3B822E0.book  Page 32  Tuesday, May 15, 2007  10:37 AM

Содержание 2008 XVS11AWX

































































































Отзывы: