Yamaha 2008 XVS11AWX Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 96

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-6

3

EAU11731

Speedometer unit

The speedometer unit is equipped with
a digital odometer and a tripmeter. The
speedometer shows riding speed. The
odometer shows the total distance trav-
eled. The tripmeter shows the distance
traveled since it was last set to zero.
Pushing the “TRIP” button switches the
display between the odometer mode
“ODO” and the tripmeter mode “TRIP”.
To reset the tripmeter, select it by push-
ing the “TRIP” button, and then push
the “TRIP” button again and hold it
down for at least one second. The trip-
meter can be used to estimate the dis-

tance that can be traveled with a full
tank of fuel. This information will enable
you to plan future fuel stops.

NOTE:

This model is not equipped with a ta-
chometer; however, it has a built-in
speed limiter, which prevents the en-
gine speed from exceeding approxi-
mately 6800 r/min and the vehicle
speed from exceeding approximately
175 km/h (110 mi/h).

EAU12347

Handlebar switches

Left

Right (XVS11X)

1. “TRIP” button

2. Odometer/tripmeter

1. Pass switch “

”

2. Dimmer switch “

/

”

3. Horn switch “

”

4. Turn signal switch “

/

”

1. Engine stop switch “

/

”

2. Start switch “

”

U3B822E0.book Page 6 Tuesday, May 15, 2007 10:37 AM

«
...
22
23
24
25
26
...
»

Содержание 2008 XVS11AWX

































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008 XVS11AWX

Бренд: ICON Страницы: 8

Бренд: KTM Страницы: 29

Tear-off machine

Бренд: Allstar Страницы: 4

Бренд: KSR Moto Страницы: 51

Бренд: hepco & becker Страницы: 4

Бренд: Wedze Страницы: 63

RACE 11621C0520

Бренд: Yoshimura Страницы: 7

Бренд: hepco & becker Страницы: 3

H-NAPE CHINSTRAP

Бренд: Fast Страницы: 24

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 12

Бренд: Yamaha Страницы: 40

Бренд: Yamaha Страницы: 53

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 110

Бренд: Yamaha Страницы: 110

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды