Yamaha 2005 YZF-R1T Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 106

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-21

6

EAU22390

Checking the front and rear
brake pads

The front and rear brake pads must be
checked for wear at the intervals spec-
ified in the periodic maintenance and
lubrication chart.

EAU22410

Front brake pads

Each front brake pad is provided with a
wear indicator, which allows you to
check the brake pad wear without hav-
ing to disassemble the brake. To check
the brake pad wear, check the position
of the wear indicator while applying the
brake. If a brake pad has worn to the

point that the wear indicator almost
touches the brake disc, have a Yamaha
dealer replace the brake pads as a set.

EAU22500

Rear brake pads

Check each rear brake pad for damage
and measure the lining thickness. If a
brake pad is damaged or if the lining
thickness is less than 1.0 mm (0.04 in),
have a Yamaha dealer replace the
brake pads as a set.

EAU22580

Checking the brake fluid level

Front brake

Rear brake

Insufficient brake fluid may allow air to
enter the brake system, possibly caus-
ing it to become ineffective.

1. Brake pad wear indicator

1. Lining thickness

1. Minimum level mark

1. Minimum level mark

U5VY21E0.book Page 21 Friday, September 10, 2004 9:21 AM

«
...
68
69
70
71
72
...
»

Содержание 2005 YZF-R1T











































































































Отзывы:

Нет отзывов

Похожие инструкции для 2005 YZF-R1T

Бренд: Cannondale Страницы: 102

Бренд: KAYO MOTOR Страницы: 74

Бренд: KAYO MOTO Страницы: 5

Бренд: Yamaha Страницы: 568

Easyrack 6617501 01 01

Бренд: hepco & becker Страницы: 4

Бренд: R&G Страницы: 6

Бренд: R&G Страницы: 2

Бренд: Honda Страницы: 61

Бренд: Salewa Страницы: 17

Бренд: Leatt Страницы: 23

Бренд: DYNATEK Страницы: 4

Бренд: DYNATEK Страницы: 11

Бренд: Honeywell Страницы: 8

Бренд: Honeywell Страницы: 304

Бренд: Hudora Страницы: 8

Бренд: Happy Trails Страницы: 2

Бренд: Protos Страницы: 6

Бренд: Norton Страницы: 69

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды