Yamaha 2005 YZF-R1T Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 106

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-16

6

EAU34300

Adjusting the engine idling
speed

The engine idling speed must be
checked and, if necessary, adjusted as
follows at the intervals specified in the
periodic maintenance and lubrication
chart.
The engine should be warm before
making this adjustment.

NOTE:

The engine is warm when it quickly re-
sponds to the throttle.

Check the engine idling speed and, if
necessary, adjust it to specification by
turning the idle adjusting screw. To in-
crease the engine idling speed, turn the
screw in direction (a). To decrease the
engine idling speed, turn the screw in
direction (b).

NOTE:

If the specified idling speed cannot be
obtained as described above, have a
Yamaha dealer make the adjustment.

EAU21381

Checking the throttle cable
free play

The throttle cable free play should mea-
sure 3.0–5.0 mm (0.12–0.20 in) at the
throttle grip. Periodically check the
throttle cable free play and, if neces-
sary, have a Yamaha dealer adjust it.

1. Idle adjusting screw

Engine idling speed:

1150–1250 r/min

1. Throttle cable free play

U5VY21E0.book Page 16 Friday, September 10, 2004 9:21 AM

«
...
63
64
65
66
67
...
»

Содержание 2005 YZF-R1T











































































































Отзывы:

Нет отзывов

Похожие инструкции для 2005 YZF-R1T

WARRIOR YFM350XS

Бренд: Yamaha Страницы: 46

Бренд: BV Powersports Страницы: 40

Бренд: R&G Страницы: 6

D14/4 BANTAM SUPREME D14/4 BANTAM SPORTS

Бренд: BSA Страницы: 120

Бренд: thousand Страницы: 32

990D0-31J50-CLE

Бренд: Suzuki Страницы: 12

COMP-MLCS-12200

Бренд: Compcooler Страницы: 11

Бренд: Arai Helmet Страницы: 12

Бренд: IBEX Страницы: 2

Бренд: Can-Am Страницы: 204

VarioProtect PANORAMA-W R-TC

Бренд: Schweißkraft Страницы: 22

Бренд: BUMOT Страницы: 5

Бренд: Petzl Страницы: 3

Бренд: Petzl Страницы: 8

Бренд: Petzl Страницы: 17

Бренд: Petzl Страницы: 24

Бренд: Orion Страницы: 156

Бренд: Benelli Страницы: 464

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды