Yale ZAPI MPW045-E Скачать руководство пользователя страница 35

Страница: 35 / 68

2200 YRM 1067

Troubleshooting

Dash Display

Controller LED

Handset or PC

AL10

LED ON (No Flashing)

Driver Shorted

CONDITION

Voltage measured at field connections is not correct.

TRUCK RESPONSE

Traction and hydraulic functions disabled.

POSSIBLE CAUSES AND TEST PROCEDURES

•

Cable connection to motor field is loose or damaged.

Verify connection of field wires to motor and con-
troller.

•

Motor field winding is shorted to chassis.

Check motor field for shorts to chassis.

•

Main contactor coil shorted/open.

Check contactor coil for correct resistance of 22.0
ohms.

Refer to the section

Electrical System

2200 YRM

1007 for more information on troubleshooting electrical

system circuits and components.

LOGIC

This fault occurs when the

voltage measured at the field connections

is not the expected value.

Dash Display

Controller LED

Handset or PC

AL66

Continuous Flashing

BATTERY LOW

CONDITION

Battery discharged and requires charging.

TRUCK RESPONSE

Hydraulic lift function disabled.

POSSIBLE CAUSES AND TEST PROCEDURES

•

Battery voltage is low.

Charge or replace battery. The battery generally
needs 8 hours to charge when fully discharged.

•

If none of previous components solved problem, then
replace controller.

LOGIC

Controller measures low

battery voltage over multiple checks during

traction or hydraulic operation.

Содержание ZAPI MPW045-E





































































Результаты поиска

Содержание ZAPI MPW045-E

Отзывы:

Бренды по названию

Популярные бренды

Yale ZAPI MPW045-E, Руководство по обслуживанию

Результаты поиска

Содержание ZAPI MPW045-E

Отзывы:

Бренды по названию

Популярные бренды