1. Rotate the base of the camera until points
are aligned, this allows for the mounting
plate to be removed.
2. Install the mounting plate on a wall or ceiling
with supplied fixing screws.
3. Align points A and B to insert the camera
base to the mounting plate. Rotate so that
points a and b are no longer aligned, this
attaches the camera securely to the base.
Note: Waste electrical products and batteries should not be disposed
of with household waste. Please recycle where facilities exist. Check
with your local authority or retailer for recycling advice.
Issue No. 1A
Information and illustrations are subject to change.
Yale reserves the right to alter the specification and
product design at any time without notice.
Due to a continuous programme of improvement,
we reserve the right to discontinue support for older
iOS and Android operating systems.
V1.1
EQ140500
Quick Installation Guide
Indoor Wireless HD IP Camera
Model: FC1405P/ FC1405PC
Package Contents
Quick Installation Guide
Resource CD
IP Camera
Quick Start Guide
Model: FC1405P/ FC1405PC
AC Adapter
USB Power Cable
1
Hardware Introduction
Physical Description
Light Sensor
Lens
Night Vision Light
Network Light
Power Light
Microphone
Micro SD Card Slot
LAN
WPS/Reset
Power
Please Note:
Only FC1405PC supports the LAN interface, but FC1405P
does not support.
Hardware Installation
1.
Rotate the base of the camera until points a and bare
aligned, this allows for the mounting plate to be
removed.
2.
Install the mounting plate on a wall or ceiling with
supplied fixing screws.
3.
Align points a and b to insert the camera base to the
mounting plate. Rotate so that points a and b are no
longer aligned, this attaches the camera securely to
the base.
a b
A
B
Hardware Connection
1.
After connect the AC power adapter to the camera,
the camera is in EZLink mode by default.
2.
Turn on your wireless router.
Before you continue, please note:
Make sure your smart phone is located near the camera.
Do not use an ethernet cable to connect the camera if
you want to use a wireless connection (Only FC1405PC).
Make sure smart phone is connected to your wireless
router.
WPS
V1.1
EQ140500
Quick Installation Guide
Indoor Wireless HD IP Camera
Model: FC1405P/ FC1405PC
Package Contents
Quick Installation Guide
Resource CD
IP Camera
Quick Start Guide
Model: FC1405P/ FC1405PC
AC Adapter
USB Power Cable
1
Hardware Introduction
Physical Description
Light Sensor
Lens
Night Vision Light
Network Light
Power Light
Microphone
Micro SD Card Slot
LAN
WPS/Reset
Power
Please Note:
Only FC1405PC supports the LAN interface, but FC1405P
does not support.
Hardware Installation
1.
Rotate the base of the camera until points a and bare
aligned, this allows for the mounting plate to be
removed.
2.
Install the mounting plate on a wall or ceiling with
supplied fixing screws.
3.
Align points a and b to insert the camera base to the
mounting plate. Rotate so that points a and b are no
longer aligned, this attaches the camera securely to
the base.
a b
A
B
Hardware Connection
1.
After connect the AC power adapter to the camera,
the camera is in EZLink mode by default.
2.
Turn on your wireless router.
Before you continue, please note:
Make sure your smart phone is located near the camera.
Do not use an ethernet cable to connect the camera if
you want to use a wireless connection (Only FC1405PC).
Make sure smart phone is connected to your wireless
router.
WPS
The Home View Camera can be free standing
or fixed in place. To mount your Home View
Camera, please follow steps 1-3 below.
Before you continue, please note:
•
Make sure your Smartphone is located near
the camera.
•
Do not use an ethernet cable to connect
the camera if you want to use a wireless
connection.
•
Make sure your Smartphone is connected to
your wireless router.
1. Connect the AC power adapter to the
camera.
2. Ensure your wireless router is turned on
and connected to the internet.
V1.1
EQ140500
Quick Installation Guide
Indoor Wireless HD IP Camera
Model: FC1405P/ FC1405PC
Package Contents
Quick Installation Guide
Resource CD
IP Camera
Quick Start Guide
Model: FC1405P/ FC1405PC
AC Adapter
USB Power Cable
1
Hardware Introduction
Physical Description
Light Sensor
Lens
Night Vision Light
Network Light
Power Light
Microphone
Micro SD Card Slot
LAN
WPS/Reset
Power
Please Note:
Only FC1405PC supports the LAN interface, but FC1405P
does not support.
Hardware Installation
1.
Rotate the base of the camera until points a and bare
aligned, this allows for the mounting plate to be
removed.
2.
Install the mounting plate on a wall or ceiling with
supplied fixing screws.
3.
Align points a and b to insert the camera base to the
mounting plate. Rotate so that points a and b are no
longer aligned, this attaches the camera securely to
the base.
a b
A
B
Hardware Connection
1.
After connect the AC power adapter to the camera,
the camera is in EZLink mode by default.
2.
Turn on your wireless router.
Before you continue, please note:
Make sure your smart phone is located near the camera.
Do not use an ethernet cable to connect the camera if
you want to use a wireless connection (Only FC1405PC).
Make sure smart phone is connected to your wireless
router.
WPS
V1.1
EQ140500
Quick Installation Guide
Indoor Wireless HD IP Camera
Model: FC1405P/ FC1405PC
Package Contents
Quick Installation Guide
Resource CD
IP Camera
Quick Start Guide
Model: FC1405P/ FC1405PC
AC Adapter
USB Power Cable
1
Hardware Introduction
Physical Description
Light Sensor
Lens
Night Vision Light
Network Light
Power Light
Microphone
Micro SD Card Slot
LAN
WPS/Reset
Power
Please Note:
Only FC1405PC supports the LAN interface, but FC1405P
does not support.
Hardware Installation
1.
Rotate the base of the camera until points a and bare
aligned, this allows for the mounting plate to be
removed.
2.
Install the mounting plate on a wall or ceiling with
supplied fixing screws.
3.
Align points a and b to insert the camera base to the
mounting plate. Rotate so that points a and b are no
longer aligned, this attaches the camera securely to
the base.
a b
a
b
Hardware Connection
1.
After connect the AC power adapter to the camera,
the camera is in EZLink mode by default.
2.
Turn on your wireless router.
Before you continue, please note:
Make sure your smart phone is located near the camera.
Do not use an ethernet cable to connect the camera if
you want to use a wireless connection (Only FC1405PC).
Make sure smart phone is connected to your wireless
router.
WPS
Network Light Status
Network Light Description
Constant Light Wired connection
Flashing every 0.2 seconds
Wireless Connection (default)
Flashing every 0.4 seconds WPS is connecting
Slow Flash every 1.0 second Wi-Fi connected
2
Add the IP Camera
You can add the IP Camera by smart phone.
1.
Download the App
You can go to the App Store or Google Play store and
search for “My IPC Viewer”. Please download and
install it.
2.
Add the IP Camera
Run the app, then you can tap the "+" button on the
app and follow the setup wizard to add your camera.
The App icon will be displayed after successful
installation:
My IPC Viewer
3
Access the IP Camera
After your camera has been successfully added, you can
access the IP Camera via the app or browser.
If you want to use your camera via the browser, you can
search and access its local website in LAN.
1.
Please copy the “Equipment Search Tool” file from the
CD to your computer.
Please Note:
Make sure the camera and PC are both in the same
Local Area Network (LAN).
2.
Open "Equipment Search Tool".
3.
Double click the camera list here, and your default
browser will open up to the login page.
4.
When logging in for the first time, you will need to
download and install the add-on.
5.
After logging in, you can manage camera through the
browser.
4
FAQ
Forget Username / Password
Please Note:
After restore to factory default settings, you need to
config the Wi-Fi connection again, you can follow
the Setup Wizard of the App to add again.
In case your device failed to add by Wi-Fi, you can
use WPS connection. please refer to the User Manual
on the CD.
Restore camera back to factory settings:
1.
Press "Reset" button for about 10 seconds with camera
powered on.
2.
Release the button and wait about 30 seconds, the
camera will automatically restart, and restore factory
settings with its username / password recovery to
admin / (blank).
1.
Go to the App Store or Google Play Store
and search for the Yale Home View App.
2.
Download and Install the App.
3. To add the IP Camera, open the App and tap
the ‘+’ button on the App and follow the
setup wizard to add your camera.
iOS
9+
Android
4.4+
Mounting Your
Home View Camera
Hardware Connection
Network Light Status
To View & Operate
Via Smartphone
